Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Describe the light pen with neat and clean figure.

2) Describe the cathode ray tube principal with properly labelled diagram.

3) Describe what sweep and extrusion method for the geometric modelling is?

4) describe what Boolean operators are? describe it with diagram.

5) Sketch the product life cycle within the computerized environment.

6) describe how the CAD technology help the engineer or the designer.

7) List various input devices and describe any one with neat and clean figure.

8) describe the functions of the geometric modelling.

9) Specify some of the advantages of using the CAM.

10) Provide the differences between the surface, line, and solid modelling.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912096

Have any Question? 


Related Questions in Mechanical Engineering

Sea water rho 1025 kgm3 flows through a pump at 021 m3s

Sea water, ρ = 1025 kg/m 3 , flows through a pump at 0:21 m 3 /s. The pump inlet is 0.25 m in diameter. At the inlet the pressure is -0.15 m of mercury. The pump outlet, 0.152 m in diameter, is 1.8 m above the inlet. The ...

Chemistry buildings built to code require a great deal of

Chemistry buildings built to code require a great deal of ventilation, which necessitates a delicate air-handling system to balance the air lowing into the building and the air lowing out. For example, if the air low out ...

The concentric joint of problem is subjected to an increase

The concentric joint of problem is subjected to an increase in temperature of 1008F. Does this increase or decrease the tension in the bolts? By how much? (Assume that the coefficient of linear expansion of the bolts is ...

It is desired to design a pump-piping system to keep a

It is desired to design a pump-piping system to keep a 1-million-gallon capacity water tank filled. The plan is to use a modified (in size and speed) version of the model A centrifugal pump. Provided is the test data for ...

1 water is flowing through a large circular conduit with a

1. Water is flowing through a large circular conduit with a velocity profile given by the equation v = 9(1- r 2 /16) fps. What is the average water velocity in the 1.5-ft pipe? 2. Water enters a 4-in. square channel as s ...

Design design all members of the 6 span truss each span is

Design: Design all members of the 6 span truss each span is 12 ft long, the height of the truss is 16 feet shown if w = 10,000 pounds. The allowable maximum tensile stress P/A is 1000 psi where P is the force in the memb ...

An air conditioner is a refrigerator with the inside of the

An air conditioner is a refrigerator with the inside of the house acting as the cold reservoir and the outside atmosphere acting as the hot reservoir. Assume that an air conditioner consumes 1.70 X 10 3 W of electrical p ...

A refrigerator is operated by a 025-hp 1 hp 746 watts

A refrigerator is operated by a 0.25-hp (1 hp = 746 watts) motor. If the interior is to be maintained at 4.50°C and the room temperature on a hot day is 38°C, what is the maximum heat leak (in watts) that can be tolerate ...

We have the task to design an industrial lift table

We have the task to design an industrial lift table according to the following principle sketch where L = 1200 mm. We should be able to control the table height between 320 mm (min height) to 1040 mm (max height), with t ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen