Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1) Describe Gibb’s phase rule equation. describe in detail two component system.

problem 2) describe in detail first law of thermodynamics. prepare a note on Enthalpy.

problem 3) Describe solubility of solids in liquids.

problem 4) prepare a detailed note on preservative action of weak acids.

problem 5) prepare a note on:

1) One component system.

2) Conductometric titrations.

3) Polymorphism.

4) Second law of Thermodynamics.

problem 6) Describe viscosity coefficient? What are Non Newtonian Fluids? Describe in detail different types of Non Newtonian Fluids.

problem 7) describe in detail various methods to determine surface and interfacial tension.

problem 8) Describe importance of particle size determination.

problem 9) prepare in short about accelerated stability studies.

problem 10) prepare a note on:

1) Flow properties of powders

2) Adsorption isotherm

3) HLB and its importance

4) Energy of activation.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M95458

Have any Question? 


Related Questions in Mechanical Engineering

A for the system of fig 347 the resistance of each line

a. For the system of Fig. 3.47, the resistance of each line cannot exceed 0.006 Ω, and the maximum current drawn by the load is 110 A. What gage wire should be used? b. Repeat (a) for a maximum resistance of 0.003 Ω, d = ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

The number of molecules crossing a unit area per unit time

The number of molecules crossing a unit area per unit time in one direction is given by where n is the number of molecules per unit volume and v is the average molecular velocity. As the average molecular velocity is app ...

Using the information given in problem and the properties

Using the information given in Problem and the properties of the standard atmosphere given in Appendix G, estimate the number of molecules per cubic inch at an altitude of 250,000 ft. Problem:- The number of molecules cr ...

Calculate the second-order correction to the energy for the

Calculate the second-order correction to the energy for the system described in Problem 6.4 and calculate the ground-state wavefunction. Account for the shape of the distortion caused by the perturbation.

Design design all members of the 6 span truss each span is

Design: Design all members of the 6 span truss each span is 12 ft long, the height of the truss is 16 feet shown if w = 10,000 pounds. The allowable maximum tensile stress P/A is 1000 psi where P is the force in the memb ...

1 find the pressure at point a2 using a liquid having a

1. Find the pressure at point A. 2. Using a liquid having a specific gravity of 1.2 and inverting a tube full of this material as shown in the figure, what is the value of h if the vapor pressure of the liquid is 3 psia?

A steel frame is fabricated with the cross section shown

A steel frame is fabricated with the cross section shown. The centered hole allows cables to be run up to equipment above. The frame supports a load P at a distance d from the centroid of the vertical beam. Bending of th ...

The maximum force applied to the tip of the allen wrench

The maximum force applied to the tip of the allen wrench before the bolt loosened is 60 N. Assume the wrench has a circular cross section with a radius 2 mm. The length of the short segment (touching the screw) is 3 cm a ...

A 15 m tall utility pole is located at a 40deg bend in a

A 15 m tall utility pole is located at a 40° bend in a set of power lines. The tension in each line is 15 kN, and due to sag of the lines, the tension forces act along directions 10° below horizontal. A guy wire has been ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen