Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Describe various capacitances, potential dividers and compare their performance for measurement of impulse voltages?

problem 2:

a) Describe one method of controlled tripping of impulse generator.

b) A 12-stage impulse generator has 0.126 µF condensers. The wave front and wave tail resistances connected are 800 ohms and 5000 ohms correspondingly. If the load condenser is 1000 pF, find out the front and tail times of the impulse wave produced.

problem 3: What do you mean by cascaded Transformer? Describe why cascading is done? describe with a neat diagram a three stage cascaded Transformer.

problem 4:

a) Derive an expression of Ripple voltage of a multistage Cockroft-Walton circuit.

b) A ten stage Cockroft-Walton circuit has all capacitors of 0.06pf. The secondary voltage of the supply transformer is 100 kV at frequency of 150 Hz. If the load current is 1 mA, find:

i) The optimum number of stages for maximum output voltage.
ii) The maximum output voltage.

problem 5: In brief describe different generating methods of high DC voltages.

problem 6: In brief describe generation of impulse voltages?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M93661

Have any Question? 


Related Questions in Electrical & Electronics

1 how would you use amperes circuital law in differential

1. How would you use Ampere's circuital law in differential form to find the magnetic field adjacent to the current sheet? 2. If the current density on the infinite plane current sheet of Figure 4.2 were directed in the ...

1 a synchronous alternator is supplying 09 pu power to the

(1) A synchronous alternator is supplying 0.9 p.u. power to the grid when a temporary three-phase short occurs on the interconnector. The power angle curves are:- Pre-fault = 2.0 sin(delta) During fault = 0.5 sin(delta) ...

Determine the spacing relative amplitudes and phase angles

Determine the spacing, relative amplitudes, and phase angles of current densities for an array of two infinite plane parallel current sheets required to obtain a radiation characteristic such that the field radiated to o ...

In a switch using the token bucket algorithm tokens are

In a switch using the token bucket algorithm, tokens are added to the bucket at a rate of r = 5 tokens/second. The capacity of the token bucket is c = 10. The switch has a buffer that can hold only eight packets (for the ...

1 discuss briefly the motional emf concept2 what is lenzs

1. Discuss briefly the motional emf concept. 2. What is Lenz's law? 3. How would you orient a loop antenna in order to obtain maximum signal from an incident electromagnetic wave which has its magnetic field linearly pol ...

1 suppose that a system is described by the impulse

1. Suppose that a system is described by the impulse response h(t) = 2sinc(t). Plot the magnitude of the frequency response of the system 2. Suppose that a system is described by the impulse response h(t) = 2sinc(t)sin(t ...

A module with 40 cells has an idealized rectangular i-v

A module with 40 cells has an idealized, rectangular I-V curve with I SC = 4 A and V OC = 20 V. If a single cell has a parallel resistance of 5Ω and negligible series resistance, draw the I-V curve if one cell is complet ...

The rate at which metallic ions are electroplated from a

The rate at which metallic ions are electroplated from a dilute electrolytic solution onto a rotating disk electrode is usually governed by the mass diffusion rate of ions to the disk. This process is believed to be cont ...

1 what are the names of the protocols discussed in this

1. What are the names of the protocols, discussed in this chapter, that provide security for e-mail? 2. How does PGP create a set of security parameters? 3. What is the purpose of the Handshake Protocol in SSL? 4. What i ...

A rectangular plastic specimen of size 100 x 100 x 10

A rectangular plastic specimen of size 100 X 100 X 10 mm 3  is placed in a rectangular metal cavity. The dimensions of the cavity are 101 X 101 X 9 mm 3 . The plastic is compressed by a rigid punch until it is completely ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro