Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Specify some of the specifications of diode and describe them.

2) Design and label the V-I characteristics of the zener diode & describe the breakdown voltage.

3) Describe the zener breakdown phenomenon in zener diode.

4) describe some of the applications each of photo diode and LED.

5) describe construction of the point contact diode with the help of diagram.

6) Describe the term schottky diode.

7) Describe the construction of LED.

8) Illustrate basic block diagram of the regulated power supply.

9) A half wave rectifier is used to applied voltage v=50sinwt and RL =1000?. Determine:-

a) DC o/p voltage

b) PIV

10) Compare full wave rectifier, half wave rectifier and the bridge rectifier.

11) Describe the working of half wave rectifier and describe the waveform with the help of diagram.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911735

Have any Question? 


Related Questions in Electrical & Electronics

Figure 319 in the text shows that des creates 16 different

Figure 31.9 in the text shows that DES creates 16 different 48-bit keys, one for each round. Why do we need 16 different keys? Why can't we use the same key in each round?

A large amount of energy e is suddenly released in the air

A large amount of energy E is suddenly released in the air as in a point of explosion. Experimental evidence suggests the radiusr of the high-pressure blast wave depends on time t as well as the energy E and ρ the densit ...

Repeat problem with the elastic constants of the plastic

Repeat Problem with the elastic constants of the plastic defined as E = 10 GPa and ν = 0.485. Problem:- A rectangular plastic specimen of size 100 X 100 X 10 mm 3  is placed in a rectangular metal cavity. The dimensions ...

1 briefly discuss the solution of the transmission-line

1. Briefly discuss the solution of the transmission-line matching problem. 2. How is the length of a short-circuited stub for a required input susceptance determined by using the Smith Chart?

1 compare the number of bits transmitted for each pcm and

1. Compare the number of bits transmitted for each PCM and DM sample if the maximum quantized value is a. 12 b. 30 c. 50 2. Answer the following questions about predictive coding: a. What are slope overload distortion an ...

1 for the force field f x2ay find the approximate value of

1. For the force field F = x 2 ay, find the approximate value of the line integral of F from the origin to the point (1, 3, 0) along a straight line path by dividing the path into ten equal segments. 2. For the force fie ...

A clean 15--efficient module stc 1 m2 in size has its own

A clean, 15-%-efficient module (STC), 1 m 2 in size, has its own 90% effi- cient inverter. Its NOCT is 44° C and its rated power degrades by 0.5%/° C above the 25° C STC. a. What would its STC rated power be? b. Find the ...

A line assumed to be infinitely long and of unknown

A line assumed to be infinitely long and of unknown characteristic impedance is connected to a line of characteristic impedance on which standing wave measurements are made. It is found that the standing wave ratio is 3 ...

Question 1a for the circuit shown in figure 1 sketch the

Question 1. (a) For the circuit shown in FIGURE 1 sketch the voltage waveform across the secondary winding of the transformer. On the same diagram sketch the load voltage waveform. The sketches should take into account d ...

An exhaust stream leaving a semiconductor fabrication plant

An exhaust stream leaving a semiconductor fabrication plant contains 4 mol % volatile organic chemical, VOC, pollutant. Twenty-five cubic meters per minute enter the bottom of a packed absorption tower and flows counterc ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen