Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) What is meant by the positive displacement pump? Describe the kinds of gear pump with the help of suitable sketch.

2) Describe what is cylinder cushioning? Describe it with neat sketch.

3) Describe the pressure control valve types with neat sketch and provide the graphic symbol.

4) Describe the flow control valve types with the neat sketch.

5) Describe the working principle of hydraulic press with neat sketch.

6) What is meant by the term PLC? Describe its working principle with the help of sketch.

7) Describe the pneumatic system for shaper machine with neat sketch.

8) Discuss the automatic reciprocating system with neat sketch.

9) describe what are the factors to be considered during the installation of pneumatic system?

10) a) Specify the merits and demerits of the pneumatic system over Hydraulic System?

b) Describe the operation of Air filter with the help of schematic diagram.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913712

Have any Question? 


Related Questions in Mechanical Engineering

Hypochlorite ion used as the chlorinating agent in swimming

Hypochlorite ion, used as the chlorinating agent in swimming pools, can decompose exothermically, in rare occasions even causing ires. he principal decomposition mechanism is believed to be a. Find the steady-state conce ...

A room has design conditions of78 f db and 50 rh and a rscl

A room has design conditions of78 F DB and 50% RH and a RSCL = 18,000 BTUlhr and RLCL = 8000 BTUlhr. An air conditioning unit supplies 900 CFM of air to the room at 58 F DB and 56 F WB. Will the unit maintain the room de ...

A compute the intrinsic gate delay of the nmost given in

(a) Compute the intrinsic gate delay of the nMOST given in the above problem and also in section 661 at the biasing condition given above. (b) Compute the intrinsic power-delay product. (c) Does the load resistor increas ...

Calculate the power factor of an electronic system subject

Calculate the power factor of an electronic system subject to a reasonable amount of harmonics given as THD(v) = 1.0%, the displacement factor is 0.92. What would be the calculated error if harmonic components were not t ...

The viscosity of heavy liquids such as oils is frequently

The viscosity of heavy liquids, such as oils, is frequently measured with a device that consists of a rotating cylinder inside a large cylinder. The annular region between these cylinders is filled with liquid and the to ...

The fugacity and fugacity coefficient are determined as a

The fugacity and fugacity coefficient are determined as a function of pressure and temperature for a model gas. These variables can be varied using sliders. The student is asked to determine the Boyle temperature and als ...

At the end of a water pipe of 3-in diameter is a nozzle

At the end of a water pipe of 3-in. diameter is a nozzle that discharges a jet having a diameter of 1½ in. into the open atmosphere. The pressure in the pipe is 60 psig (pounds per square inch gage), and the rate of disc ...

1 in more than one paragraph but less than a page discuss

1. In more than one paragraph but less than a page, discuss some of the failure modes experienced in the collapse of the World Trade Center and how they might have been prevented. 2. A truss ABC supports a load W at join ...

I need a proposal project for surface metrology asap i need

I need a proposal project for Surface Metrology ASAP. I need two documents: 1. Project outlines Proposal outlines (the instruction & template is in the attached Proposal for the project) should be 1 page 2. Final project ...

In a chemical plant a solution of density 1100kgm3 and

In a chemical plant a solution of density 1100kg/m3 and specific heat capacity 4.6 kJ/kg-Kis to be heated from 65 OC to 100OC. The required flow rate of the solution is 11.8 kg/s. Atubular heat exchanger is used for this ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen