Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. Describe the process of electrical discharge machining, its process parameters and applications in detail.

2. describe the working, applications and advantages of wire cut EDM equipment in detail.

3. (i) With the help of neat and suitable sketch, describe the EDM process.

(ii) Describe briefly advantages of wire EDM process.

4. (i) Describe the classification and characteristics of various spark erosion generators.

(ii) With help of neat and suitable sketch describe the mechanism of material removal in EDM.

5.(i) Describe the working principle, elements and characteristics of wire EDM.

(ii) Describe how stratified wire works. Also describe about recent developments in wire EDM.

6. What do you mean by ECM?

7. prepare down the factors which influence oxidation in ECM?

8. prepare down the materials which are used to make the tool electrode?

9. prepare down the major functions of electrolysis in the ECM?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911696

Have any Question? 


Related Questions in Mechanical Engineering

List three ways to control preload directly what are the

List three ways to control preload directly ? What are the advantages of a bonded ultrasonic transducer? What is sometimes cited as a disadvantage? Can torque be used to tighten a 6 in. diameter bolt? If not, why not? Na ...

Blood glucose concentration is regulated primarily by the

Blood glucose concentration is regulated primarily by the controlled release of insulin in the pancreas. However, patients with Type I diabetes mellitus are incapable of producing insulin and therefore require shots of i ...

A cantilever beam ab supports a uniform load of intensity q

A cantilever beam AB supports a uniform load of intensity q acting over part of the span and a concentrated load P acting at the free end, as shown. Determine the deflection and slope at end B of the beam. The beam has l ...

Problem 1-consider a 5-m-long constantan block k 23 wmk30

Problem 1-Consider a 5-m-long constantan block (k = 23 W/mK) 30 cm high and 50 cm wide. The block is completely submerged in iced water at 0 °C that is well stirred, and the heat transfer coefficient is so high that the ...

1 if the density of sea water is approximated by the

1. If the density of sea water is approximated by the equation of stat is the compressibility, determine the pressure and density at a point 32,000 ft below the surface of the sea. Assume β = 300,00 psi. 2. The change in ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

Please reference any source of outside information as

Please reference any source of outside information as needed to answer these questions. 1. In a frozen food plant, atmospheric air is to go through a pre-cooler to be partially dehydrated so that during its passage throu ...

1 calculate the following for the function fx e-3x - 2xa

1) Calculate the following for the function f(x) = e -3x - 2x. a. Calculate the derivation of the function by hand. Write a MATLAB function that calculates the derivative of this function and calculate the derivative at ...

1 if the design load is 90 kn 20300 lbf what is the dead

1. If the design load is 90 kN (20,300 lbf), what is the dead load and what is the intensity of the dead load in the light of the live load calculation of Problem CS1.1? 2. Determine the specific weight of lightweight co ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro