Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1)(a) Describ how balanced modulator is used to generate SSB AM wave with a neat and suitable diagram.

(b) For a modulation Co-efficient m=0.2 and an unmodulated carrier power Pc = 1000W, find out

(i) Total sideband power

(ii) Upper and Lower side band power

(iii) Total transmitted power.

2) With a neat and suitable diagram describe the working principle and operation of Super Hetrodyne AM receiver and prepare down its advantage over TRF receivers.

3) Describe the working operation of FM Reactance modulator by using essential diagrams and equations.

4) Describe the principle and working of Foster Seeley Discriminator with suiatble diagram.

5) Describe about the operation of a PCM based Communication system in detail.

6) Define and prove Nyquist’s sampling Theorem.

7) With a neat and suitable block diagram describe the operation of QPSK transmitter and Receiver.

8) Describe the operation of M-ary FSK based communication system with a neat and suitable diagram and prepare down it’s advantages over other system.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913430

Have any Question? 


Related Questions in Electrical & Electronics

1 we defined two security services for e-mail pgp and smime

1. We defined two security services for e-mail (PGP and S/MIME). Explain why e-mail applications cannot use the services of SSL/TLS and need to use either PGP or S/MIME. 2. Assume Alice needs to send an e-mail to Bob. Ex ...

1 discuss briefly the motional emf concept2 what is lenzs

1. Discuss briefly the motional emf concept. 2. What is Lenz's law? 3. How would you orient a loop antenna in order to obtain maximum signal from an incident electromagnetic wave which has its magnetic field linearly pol ...

Approximate by a number of terms of your choice through the

Approximate (by a number of terms of your choice) through the three forms of Fourier series expansion the periodic signal that in one period is given by Each time, a. Plot the approximate signal in time of three periods. ...

1 how do you find the work done in moving a test charge by

1. How do you find the work done in moving a test charge by an infinitesimal distance in an electric field? 2. What is the amount of work involved in moving a test charge normal to the electric field? 3. What is the phys ...

1 consult an appropriate reference book and compare the

1. Consult an appropriate reference book and compare the procedure used for obtaining the electromagnetic field due to the Hertzian dipole with the procedure used here. 2. What are radiation fields? Why are they importan ...

1 why is it that the distances r1 and r2 in the phase

1. Why is it that the distances r 1 and r 2 in the phase factors in equations (8.47a) and (8.47b) cannot be set equal to r, but the same quantities in the amplitude factors can be set equal to r? 2. What is an array fact ...

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

1 in kademlia assume m 4 and active nodes are n4 n7 and

1. In Kademlia, assume m = 4 and active nodes are N4, N7, and N12. Where is the key k3 stored in this system? 2. In Chord, assume the size of the identifier space is 16. The active nodes are N3, N6, N8, and N12. Show the ...

1 for flow at very low speeds and with large viscosity the

1. For flow at very low speeds and with large viscosity (the so-called creeping flows) such as occur in lubrication, it is possible to delete the inertia terms, Dv/Dt, from the Navier- Stokes equation. For flows at high ...

Assignmentpart 1 electricians tools1 which of the following

Assignment Part 1: Electricians' Tools 1. Which of the following types of symbols would be used on an electrical drawing for a large machine? A. Schematic symbols B. Blueprint symbols C. Pictorial symbols D. Wiring symbo ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro