Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) describe how materials handling equipment are categorized?

2) prepare down the types of chain drive mechanisms and describe any one in detail.

3) Describe the working of bucket elevator with a neat and suitable sketch.

4) What is meant by screw conveyor? Describe in detail with a neat and suitable sketch.

5) prepare down the different types of cranes, with a neat and suitable sketch describe any one in detail.

6) prepare down type of grabbing attachments which are used for loose materials, describe any one in detail.

7) Describe how will you categorize material handling equipments? describe their characteristics with suitable ex.

8) Describe the methods of handling the material by overhead in the industrial building.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912549

Have any Question? 


Related Questions in Mechanical Engineering

A cantilever beam ab supports a uniform load of intensity q

A cantilever beam AB supports a uniform load of intensity q acting over part of the span and a concentrated load P acting at the free end, as shown. Determine the deflection and slope at end B of the beam. The beam has l ...

A water-filled u-tube manometer is used to measure the

A water-filled U-tube manometer is used to measure the pressure inside an air tank. The water level in the U-tube on the side connected to the tank is 5 ft above the base of the tank. The water level in the other side of ...

What is the difference between initial and residual preload

What is the difference between initial and residual preload? Typically, what percentage of the work we do with a torque wrench ends up as preload in an individual bolt? Is the preload mentioned above initial or residual ...

Name the principal modes of failure of both tensile and

Name the principal modes of failure of both tensile and shear joints? Describe or list the criteria a bolted joint designer must consider when selecting bolt size and material for a new joint? Will short, fat bolts gener ...

A distribution function such as the maxwell-boltzmann

A distribution function such as the Maxwell-Boltzmann distribution can be described in terms of moments, where the nth moment of a distribution P(x) is written (he moment does not have to be evaluated relative to the mea ...

An incompressible fluid flows past a flat plate as in the

An incompressible fluid flows past a flat plate, as in the figure below, with a uniform inlet profile and a polynomial exit profile Compute the volume flow Q across the top surface of the control volume. The plate has wi ...

Name at least four factors which can reduce in-service

Name at least four factors which can reduce in-service clamping force? Name at least three factors which can be prevented or at least reduced by sufficient in-service clamping force? Name at least four factors which dete ...

The case study kahiki-foods-case-study critique it and do a

The case study kahiki-foods-case-study CRITIQUE it and do a 10-12 pages report about it their are notes and a presentation done about it that you can use in doing the paper Also their is an example of a different case wh ...

Determine the maximum in-plane stresses for a cylindrical

Determine the maximum in-plane stresses for a cylindrical tank made of steel (E = 205 GPa, ν = 0.30), having a mean radius of 2 m and a thickness of 20 mm, and subjected to an internal pressure p = 1 MPa.

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen