Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) What is Ritz approach used in FEM?

problem 2) What do you mean by isoparametric elements?

problem 3) describe ‘shape function’ in detail.

problem 4) prepare down the Gauss Quadrature rule used in FEA?

problem 5) prepare down the two characteristics of global stiffness matrix.

problem 6) What are the various sources of errors in FEA?

problem 7) What do you mean by ‘axisymmetric elements’?

problem 8) prepare down the difference between a rectangular and a quadrilateral element?

problem 9) Describe the use of natural coordinate system in FEM.

problem 10) prepare down the factors for selection of type of element used for mesh generation in FEA.

problem 11) Derive the element stiffness matrix for a 2-D beam problem Using Galerkin approach.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98971

Have any Question? 


Related Questions in Mechanical Engineering

A room has design conditions of78 f db and 50 rh and a rscl

A room has design conditions of78 F DB and 50% RH and a RSCL = 18,000 BTUlhr and RLCL = 8000 BTUlhr. An air conditioning unit supplies 900 CFM of air to the room at 58 F DB and 56 F WB. Will the unit maintain the room de ...

During the test of a centrifugal pump a bourdon pressure

During the test of a centrifugal pump, a Bourdon pressure gage just outside the casing of the 12-in.-diameter suction pipe reads 6 psig (i.e., vacuum). On the 10-in. -diameter discharge pipe another gage reads 40 psig. T ...

1 in more than one paragraph but less than a page discuss

1. In more than one paragraph but less than a page, discuss some of the failure modes experienced in the collapse of the World Trade Center and how they might have been prevented. 2. A truss ABC supports a load W at join ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

1 the dam shown below is 100 m wide determine the magnitude

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface. 2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant f ...

Define the endurance limit of a bolt which is greater the

Define the endurance limit of a bolt ? Which is greater, the static yield strength or the endurance limit of the bolt? When will an increase in preload increase fatigue life? When will an increase in preload decrease fat ...

What do we mean by the term torque reaction a right angle

What do we mean by the term torque reaction? A right angle nut runner is used to produce 500 ft-lb of torque on a bolt having a 7/8 -9 UNC thread. The tool is 18 in. long. How much reaction force, created by the reaction ...

A simply supported beam 5 m long is loaded with a 20 n

A simply supported beam 5 m long is loaded with a 20 N downward force at a point 4 m from the left support. The second moment of area of the cross-section of the beam is 4I 1 for segment AB and I 1 for the remainder of t ...

What primary factors determine the number of load cycles

What primary factors determine the number of load cycles required to break a bolt subject to fatigue loading? Describe the appearance of the break surface of a bolt which has failed in fatigue ? Where on a bolt are you m ...

Figure a shows a steel i-beam cross section note not

Figure (a) shows a steel I-beam cross section (note, not symmetric about the y axis). Two steel plates with cross section 10 mm × 200 mm are welded to the beam. Figure (b) and the 3D inset show the configuration of the c ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro