Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) Describe the steps involved in development of Visual Basic Application.

problem 2) prepare down a Visual Basic program to determine the given number is odd or not, and outputting data to a message box.

problem 3) What will be the values of x after the execution of each step one by one.

x = 1
If x < 5 Then
x = 0
End If
x = x + 1

problem 4) Describe the properties, Events related and method associated with Button, list Box, and Combo Box in VB.

problem 5) What do you mean by an Array? How we can declare a fixed length array and dynamic Array.

problem 6) Describe the following statement in VB

(a) If .Else statement.

(b) Case. End Select statement.

problem 7) prepare down guidelines to create an effective menu. Also provide code to create a top down menu.

problem 8) prepare a detailed note on MDI forms.

problem 9) What do you mean by MSFlexGrid control and describe how it is used?

problem 10) Describe the usage of Bound controls in ActiveX data controls.

problem 11) Describe steps involved to access the data from a data base in Visual Basic in detail.

problem 12) prepare a detailed note on crystal and data reports generated in VB.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98987

Have any Question? 


Related Questions in Mechanical Engineering

The maximum force applied to the tip of the allen wrench

The maximum force applied to the tip of the allen wrench before the bolt loosened is 60 N. Assume the wrench has a circular cross section with a radius 2 mm. The length of the short segment (touching the screw) is 3 cm a ...

Name at least four factors which can reduce in-service

Name at least four factors which can reduce in-service clamping force? Name at least three factors which can be prevented or at least reduced by sufficient in-service clamping force? Name at least four factors which dete ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

Sketch a joint diagram for a joint in the preloaded

Sketch a joint diagram for a joint in the preloaded condition, before an external load is applied to the joint. Assume that KJ = 5 KB ? We apply 43 ft-lbs of torque to a 3=8-28 2 J429, GR 8 bolt. We believe that the nut ...

Many devices have been developed to measure the viscosity

Many devices have been developed to measure the viscosity of fluids. One such device, known as a rotational viscometer, involves a pair of concentric cylinders with radii r i and r o , and total length L. The inner cylin ...

Calculate the size h of the two welds required to attach a

calculate the size h of the two welds required to attach a plate to a frame as shown in figure. if the plate supports an inclined force P=50kn. use a factor safety of 3 and yield shear stress of 350 mpa for the weld mate ...

1 an equation linking water density and pressure iswhere

1. An equation linking water density and pressure is where the pressure is in atmospheres and B =3000 atm. Determine the pressure in psi required to increase water density by 1% above its nominal value. 2. What pressure ...

1 what is the pressure panbspin the figure the specific

1. What is the pressure p A  in the figure? The specific gravity of the oil is 0.8. 2. Find the difference in pressure between tanks A and B, if  d 1 = 2ft, d 2 = 6 in., d 3 = 2.4 in., and d 4 = 4 in. 3. What is the pres ...

In adiabatic demagnetization we use a magnetic ield to

In adiabatic demagnetization, we use a magnetic ield to couple away almost all of the residual energy of a crystal that has been cooled to 2.2 K by liquid helium. (We can get below the normal boiling point of liquid heli ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen