+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

1) describe Pascal’s Law. Describe it with the help of an ex.

2) Distinguish between Fixed displacement pump and Variable displacement pump.

3) A double acting cylinder is used to push and pull 10,000N and they have 10mm2 and 5mm2 area on the piston and rod side areas. Find the pressure induced due to loads.

4) Describe the special feature of telescopic cylinder.

5) describe what is meant by “cushioning of cylinders”?

6) Design the symbol of 4/3 DCV solenoid and pressure relief valve.

7) Specify how the Quick return is obtained in the Hydraulic shaper.

8) Specify some of the fluid conditioners.

9) Describe the logic function of & element.

10) describe what are Mufflers?

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M913513

Have any Question?

## Related Questions in Mechanical Engineering

### The velocity profile in the annular control volume of

The velocity profile in the annular control volume of Example is approximately linear, varying from a velocity of zero at the outer boundary to a value of ωd/2 at the inner boundary. Develop an expression for the fluid v ...

### Wind tunnel testing of the concrete reef balls used in

Wind tunnel testing of the concrete reef balls used in artificial reefs is proposed. A typical reef ball (e.g. Figure 1.2) has a diameter of 6 ft, and is immersed in sea water. A scale model is prepared with diameter of ...

### A linear spring k is to be designed to stop a 20-mg

a linear spring k is to be designed to stop a 20-mg railroad car traveling at 8km/h within 400 mm after impact. Find the smallest value of k that will produce the desired result.

### The illustration below shows a vane with a turning angle

The illustration below shows a vane with a turning angle θ which moves with a steady speed v c . The vane receives a jet that leaves a fixed nozzle with speed θ. (a) Assume that the vane is mounted on rails as shown in t ...

### In a small generating system there are two generators in

In a small generating system, there are two generators in parallel. One of them is a synchronous generator, and the other, an IG. The common load is 3.0 kW with a power factor of 0.92. If the IG supplies only 1.0 kW of t ...

### The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

### Question 1 -1 plot the singular stress components sigmaxx

Question 1 - 1) Plot the singular stress components, σ xx , σ yy and τ xy for a cracked body under Mode I, Mode II and Mode III loading with a stress intensity factor K i = 10 MPa·m 1/2 (i = I, II and III). Plot the stre ...

### 1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

### Introductionemployers are constantly asking for engineering

Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers need to be creative and innovative. They have to ...

### 1 two clean and parallel glass plates separated by a gap of

1. Two clean and parallel glass plates, separated by a gap of 1.625 mm, are dipped in water. If σ = 0.0735 N/m, determine how high the water will rise. 2. A glass tube having an inside diameter of 0.25 mm and an outside ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro