Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Describe about the various configuration of Robots with the neat and suitable sketch in detail.

2) Describe the spatial resolution accuracy and repeatability of Robots in detail.

3) Describe different mechanical grippers which are used as end effectors with a neat and suitable sketch

4) describe about the drive systems used in robots in detail.

5) prepare brief notes on sensors.

6) Describe image segmentation and training of vision systems

7) prepare brief notes on:

a) safety in robotics

b) Robot cell layouts

c) Robot cycle time

8) Describe why robots are favoured in welding application and prepare down robot configuration, that are used for spot welding.

9) Describe about the applications of robots in medical fields in detail.

10) Describe how the robots are used in characterization of root surface.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912371

Have any Question? 


Related Questions in Mechanical Engineering

Projectdesign a tube bank that will increase the

Project Design a tube bank that will increase the temperature of a 1200 CFM flow of air from 35°F to 100°F. Assume a constant pressure of 1atm. Each tube will have a diameter of 0.5in and a length of 24in. The tube confi ...

1 the pump in the boat shown pumps 6 ft3nbsps of water

1. The pump in the boat shown pumps 6 ft 3  /s of water through a submerged water passage, which has an area of 0.25 ft 2  at the bow of the boat and 0.15 ft 2  at the stern. Determine the tension in the restraining rope ...

Calculate the fraction of n2 molecules in a sample at 298 k

Calculate the fraction of N2 molecules in a sample at 298 K that have speeds less than 10.0ms -1 by integrating the Maxwell-Boltzmann distribution over the appropriate range of speeds (just writing the correct integral i ...

For a deck supports of length 325 m are proposed to be

For a deck, supports of length 3.25 m are proposed to be built from aluminum with a Young's modulus of 72 GPa and a yield stress of 480 MPa. A cylindrical design is proposed with outer diameter d = 100 mm and wall thickn ...

A watertight bulkhead 22 ft high forms a temporary dam for

A watertight bulkhead 22 ft high forms a temporary dam for some construction work. The top 12 ft behind the bulkhead consists of sea water with a density of 2 slugs/ft 3  , but the bottom 10 ft begin a mixture of mud and ...

You have been introduced to a number of different tools

You have been introduced to a number of different tools that can be used to help IE's and MfgE's analyze and develop solutions to make processes more effective and efficient. Watch the video located at http://www.iienet2 ...

It is desired to use a 075-m diameter beach ball to stop a

It is desired to use a 0.75-m diameter beach ball to stop a drain in a swimming pool. Obtain an expression that relates the drain diameter D and the minimum water depth h for which the ball will remain in place.

You need a reort if 10 pages and above the report about

You need a reort if 10 pages and above. the report about colorimeter specificly measuring spesific heat. anything you need will be provided. format sample has been will be provided. and a report sapmle will be provided t ...

Assigned work clearly indicate all assumptions and

Assigned Work (Clearly indicate all assumptions and references) 1. A 500 m 2 light colored swimming pool is located at (a) normal suburban site, (b) well-sheltered site, where the measured wind speed at 10 m height is 3 ...

1 consider the differential control volume shown below by

1. Consider the differential control volume shown below. By applying the conservation of mass and the momentum theorem, show that dP + pvdv + g dy = 0 2. Water flows steadily through the horizontal 30° pipe bend shown be ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen