Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Describe the multi quadrant operation of the low speed hoist within speed torque plane in detail.

2) Deduce the expression for heating time constant and sketch the cooling and heating curves.

3) Describe the operation of single phase fully-controlled converter fed dc separately excited motor in continuous and discontinuous modes of operation with necessary waveforms.

4) a) Describe the several control techniques of the chopper controlled DC Drives.

b) Also describe what is meant by the Ward Leonard scheme.

5 ) Describe the static Kramer variable speed drive system used for slip power recovery with neat sketch.

6) Describe the method of control of 3- phase induction motor by

a) Stator voltage control

b) Frequency control

7) Describe cyclo- converter fed synchronous motor drive with neat diagram. describe in detail.

8) Describe the self-controlled synchronous motor drive by using the load commutated thyristor inverter.

9) Describe the control scheme for steel rolling mills with suitable diagram.

10) Sketch the appropriate diagram and discuss the DSP based control of the electric drive.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913204

Have any Question? 


Related Questions in Electrical & Electronics

In problem find the rate of discharge if the frictional

In Problem , find the rate of discharge if the frictional head loss in the pipe is 3.2 v2 /g where v is the flow velocity in the pipe. Problem:- Referring to the figure, assume the flow to be frictionless in the siphon. ...

1 what is the magnetic flux crossing an infinitesimal

1. What is the magnetic flux crossing an infinitesimal surface oriented parallel to the magnetic flux density vector? 2. For what orientation of the infinitesimal surface relative to the magnetic flux density vector is t ...

1 what is the direction of the magnetic field for a uniform

1. What is the direction of the magnetic field for a uniform plane wave having its electric field in the positive z-direction and propagating in the positive x-direction? 2. What is intrinsic impedance? What is its value ...

A 12-bit oversampling adc oversamples by a factor of m 64

A 12-bit oversampling ADC oversamples by a factor of M = 64. To achieve the same average power of the quantization noise at the output, but without using oversampling, how many bits are required?

1 describe the phenomenon of the bouncing back and forth of

1. Describe the phenomenon of the bouncing back and forth of transient waves on a transmission line excited by a constant voltage source in series with internal resistance and terminated by a resistance. 2. Discuss the v ...

1 if the plate shown is inclined at an angle as shown what

1. If the plate shown is inclined at an angle as shown, what are the forces F x  and F y  necessary to maintain its position? The flow is frictionless. 2. A steady, incompressible, frictionless, two-dimensional jet of fl ...

In a chord network with m 4 node n2 has the following

In a Chord network with m = 4, node N2 has the following finger-table values: N4, N7, N10, and N12. For each of the following keys, first find if N2 is the predecessor of the key. If the answer is no, find which node (th ...

Calculate the approximate diameter and length of stator

Calculate the approximate diameter and length of stator core, the number of stator slots and the number of conductors for a 20KW,400V,3 phase,4pole,1200rpm,delta connected induction motor. Bav=0.5T, Kw=0.82, ac=26000amp. ...

1 explain why rtp cannot be used as a transport-layer

1. Explain why RTP cannot be used as a transport-layer protocol without being run on the top of another transport-layer protocol such as UDP. 2. Both TCP and RTP use sequence numbers. Do sequence numbers in these two pro ...

A line assumed to be infinitely long and of unknown

A line assumed to be infinitely long and of unknown characteristic impedance is connected to a line of characteristic impedance on which standing wave measurements are made. It is found that the standing wave ratio is 3 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen