Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1.a) prepare down the advantages and disadvantages of nuclear power plant?

b) Describe with a neat and suitable sketch the indirect gas cooled reactor

2.a) Describe the principle of operation of sodium graphite reactor in detail.

b) Deduce the expression for maximum hydraulic efficiency in impulse turbine

3.a) Distinguish pelton wheel turbine with Francis turbine.

b) Describe radial flow and axial flow turbo machines in detail.

4.a) What do you mean by specific speed of a turbine? Deduce the expression for the specific speed.

b) Describe the term unit power, unit speed and unit discharge with reference to a turbine

5. Describe function of draft tube in turbines and the different kinds of draft tubes.

6. Sketch a layout of a typical micro hydro scheme and describe its working in detail.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911741

Have any Question? 


Related Questions in Mechanical Engineering

Calculate the size h of the two welds required to attach a

calculate the size h of the two welds required to attach a plate to a frame as shown in figure. if the plate supports an inclined force P=50kn. use a factor safety of 3 and yield shear stress of 350 mpa for the weld mate ...

Magnet wire is single-strand wire with a thin insulation

Magnet wire is single-strand wire with a thin insulation layer (of enamel, varnish, glass, etc.) to prevent short circuits. In a production facility, copper (E = 120 GPa, σ ys = 70 MPa) magnet wire is to be coated with v ...

Name several ways by which the loss of initial preload can

Name several ways by which the loss of initial preload can be reduced ? Roughly how much embedment relaxation could we expect from new parts used in a non-gasketed, steel joint? Define elastic interactions. How can elast ...

The concentric joint of problem is subjected to an increase

The concentric joint of problem is subjected to an increase in temperature of 1008F. Does this increase or decrease the tension in the bolts? By how much? (Assume that the coefficient of linear expansion of the bolts is ...

1 a 1968 volkswagen sedan is driving over a 7300-ft-high

1. A 1968 Volkswagen sedan is driving over a 7300-ft-high mountain pass at a speed of v m/s into a headwind of W m/s. Compute the gage pressure in mPa at a point on the auto where the velocity relative to the auto is v - ...

1 in a hartree-fock scf calculation on the chlorine atom

1. In a Hartree-Fock SCF calculation on the chlorine atom using 20 (spatial) basis functions, how many virtual orbitals are determined? 2. Give an example of a restricted Hartree-Fock wavefunction and an unrestricted Har ...

1 what requirements control the derivation of load-stress

1. What requirements control the derivation of load-stress relations? 2. Describe the method of mechanics of materials. 3. How arc stress-strain-temperature relations for a material established? 4. Explain the difference ...

A 1 in times 10 in plank on a redwood deck has l 48 in

A 1 in × 10 in plank on a redwood deck has L = 48 in long and supported on three joists that rest on the ground and so do not bend. The joists act as pin/roller supports for the plank. If a 130 lb person stands on the pl ...

1 using matlabsimulinkreg write a computer program to

1. Using MATLAB/Simulink®, write a computer program to represent the SEIG in its transient state. 2. Explain why an IG cannot self-excite under the following conditions: (1) no residual magnetism, (2) after too much indu ...

If the kansas city building code specified that a floor

If the Kansas City Building Code specified that a floor structure must support a live load of 4.79 kPa (100 psf), and if the walkway length L = 9.1 m = 30.0 ft and width b = 2 m = 6.56 ft, what contribution is made to th ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro