Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) a) Describe the several modes of the operation of thyristor with the help of static VI characteristics.

b) Sketch the two transistor model of SCR and find out the α and β.

2) Sketch the basic structure of the power MOSFET and discuss the transfer and the output characteristics

3) Describe the working of the 1Φ full converter with the RL load and deduce the expression for average and for the rms value.

4) Describe the working of the 3Φ full converter for the RLE load by giving the waveforms.

5) Describe the operation of the Four Quadrant Chopper along with RLE Load.

6) Describe the working of the Single phase step up and step down cycloconverter with the help of neat and clean waveforms.

7) Discuss the operation of three phase 1800 with well describeed waveform.

8) describe what is meant by the PWM? Describe the different techniques with the help of neat waveforms.

9) describe the several configurations of UPS with the help of block diagram.

10) With the help of neat circuit and waveforms, describe the mode inverter.

a) Flyback SMPS .

b) Push pull SMPS.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913295

Have any Question? 


Related Questions in Electrical & Electronics

Find the disruptive and visual corona voltage of a grid

find the disruptive and visual corona voltage of a grid line operating at 132kv ,conductor diameter =1.9cm,conductor spacing =3.81m,temp=44,pressure=73.7,conductor surface factor ;fine weather=0.8;rough weather=0.66

1 when is it meaningful to attribute a group velocity to a

1. When is it meaningful to attribute a group velocity to a signal comprised of more than two frequencies? Why? 2. Discuss the propagation of a narrow-band amplitude modulated signal in a dispersive channel. 3. Discuss t ...

1 considering the second hand on your watch to be a vector

1. Considering the second hand on your watch to be a vector, state its polarization. What is the frequency? 2. What is a phasor? 3. Is there any relationship between a phasor and a vector? Explain. 4. Describe the phasor ...

1 a determine the transfer function vosv1 s for the circuit

1. (a) Determine the transfer function Vo(s)/V1 (s) for the circuit shown below. (b) From the transfer function identify what type of filter it is. (c) Justify your answer of part b 2. (a) Draw the circuit of a free runn ...

1 what is the total distance around the circumference of a

1. What is the total distance around the circumference of a circle of radius 1 m? What is the total vector distance around the circle? 2. What is the total surface area of a cube of sides 1 m? Assuming the normals to the ...

Consider the problem of performing system identification as

Consider the problem of performing system identification as shown previously in Figure 9.49. Suppose the system to be identified is the following IIR filter. Write a MATLAB program that uses the FDSP toolbox function f l ...

1 how would you use amperes circuital law in differential

1. How would you use Ampere's circuital law in differential form to find the magnetic field adjacent to the current sheet? 2. If the current density on the infinite plane current sheet of Figure 4.2 were directed in the ...

1 in kademlia assume m 4 and active nodes are n4 n7 and

1. In Kademlia, assume m = 4 and active nodes are N4, N7, and N12. Where is the key k3 stored in this system? 2. In Chord, assume the size of the identifier space is 16. The active nodes are N3, N6, N8, and N12. Show the ...

1 why is it necessary to have the minus sign associated

1. Why is it necessary to have the minus sign associated with the time rate of increase of magnetic flux on the right side of Faraday's law? 2. What is electromotive force? 3. What are the different ways in which an emf ...

Microelectronics1 what regions are heavily doped n to form

Microelectronics 1. What regions are heavily doped n+ to form ohmic contacts? 2. On the plot to the right. label the horzontal and vertical axis. Indicate the triode and square law regions. The square law region of secon ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro