Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1. Describe the operating mode0 of 8051 serial ports in detail.

2. Describe the operating mode2 of 8051 serial ports in detail.

3. Describe the mode3 of 8051 serial ports in detail.

4.prepare down a program to carry out multiplication of 2 numbers by using 8051.

5. prepare down the addressing modes of 8051.

6. describe about CALL statement in 8051 in detail.

7. describe about the jump statement in detail.

8. prepare down a program to load accumulator ,DPH,&DPL by using 8051.

9. What do you mean by subroutine or procedure?

10. What is the role of SWAP?

11. describe Assembly Language Program with suitable disgram.

12. What do you mean by debugging.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99231

Have any Question? 


Related Questions in Electrical & Electronics

1 what does the word retarded in the terminology retarded

1. What does the word retarded in the terminology retarded magnetic vector potential refer to? Explain. 2. Discuss the application of the magnetic vector potential in the determination of the electromagnetic fields due t ...

1 derive the weak form of a two-dimensional steady-state

1. Derive the weak form of a two-dimensional, steady-state heat transfer problem. 2. Derive the weak form of a simply supported beam problem.

1 what is the laplacian of a scalar what is its expansion

1. What is the Laplacian of a scalar? What is its expansion in Cartesian coordinates? 2. State Poisson's equation. 3. Outline the solution of Poisson's equation for the potential in a region of known charge density varyi ...

The spacing a between the plates of a parallel-plate

The spacing a between the plates of a parallel-plate waveguide is equal to 5 cm. The dielectric between the plates is free space. If a generator of fundamental frequency 1800 MHz and rich in harmonics excites the wavegui ...

1 discuss with the aid of an example the discharging of an

1. Discuss with the aid of an example the discharging of an initially charged line into a resistor. 2. Discuss the bounce-diagram technique of transient analysis of a line with uniform initial voltage and current distrib ...

1 explain why rtp cannot be used as a transport-layer

1. Explain why RTP cannot be used as a transport-layer protocol without being run on the top of another transport-layer protocol such as UDP. 2. Both TCP and RTP use sequence numbers. Do sequence numbers in these two pro ...

1 discuss how the cutoff condition arises in a waveguide2

1. Discuss how the cutoff condition arises in a waveguide. 2. Explain the relationship between the cutoff wavelength and the spacing between the plates of a parallel-plate waveguide based on the phenomenon at cutoff.

1 in polar coordinates show that2 determine the fluid

1. In polar coordinates, show that 2. Determine the fluid rotation at a point in polar coordinates, using the method illustrated in given figure.

A 9 kva 208 v l-l 3-phase y connected stator synchronous

A 9 kVA, 208 V (L-L), 3-phase Y connected stator, synchronous generator has a stator resistance of 0.1 ohm per phase, and a synchronous resistance of 5.6 ohm per phase. The generator is driven by a diesel engine, and is ...

1 define standing wave ratio swr what are the standing wave

1. Define standing wave ratio (SWR). What are the standing wave ratios for (a) an infinitely long line, (b) a short-circuited line, (c) an open-circuited line, and (d) a line terminated by its characteristic impedance? 2 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen