Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

problem 1: Describe the merits and demerits of Design and Construct contracts compared to other procurement methods.

problem 2: Describe the financial risks a contractor is exposed to and how such can be minimized both at tendering and construction stages of a design and construct contract.

problem 3: Describe procurement options for highway improvement schemes.

problem 4: What are the merits and demerits of design and construct contracts by comparison with other procurement methods? Describe, giving exs from your own experience.

problem 5: Describe how cost risks are identified and managed in the feasibility, design, tender and construction of a project. How does consideration of cost risk influence the choice of method of procurement?

problem 6: Describe the basis of Design Build Finance and Operate for procuring a main public sector project.

What do you consider to be the main merits and demerits of this method of procurement for clients, consultants and contractors?

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M93861

Have any Question? 


Related Questions in Civil Engineering

The door header in fig 7c supports a dead load of 120 lbft

The door header in Fig. 7.C supports a dead load of 120 lb/ft and a roof live load of 120 lb/ft. Lumber is No. 2 Hem-Fir. C M = 1.0, C t = 1.0, and C i = 1.0. There are no bolt holes at the point of maximum moment. Later ...

Suppose you are shown this circuitwithout any analysis-just

Suppose you are shown this circuit: Without any analysis-just by looking at the circuit-you should be able to tell whether it does or does not have a hazard. Explain how you can do this and indicate whether or not this c ...

In this chapter we have designed three different neural

In this chapter we have designed three different neural networks to distinguish between apples and oranges, based on three sensor measurements (shape, texture and weight). Suppose that we want to distinguish between bana ...

We have three inputoutput prototype vector pairsi show that

We have three input/output prototype vector pairs: i. Show that this problem cannot be solved unless the network uses a bias. ii. Use the pseudoinverse rule to design a network for these prototype vectors. Verify that th ...

1 what is the difference between the construction of

1. What is the difference between the construction of interior and exterior plywood? 2. Briefly describe the span rating found in the grade-trademark of the following panels: a. Sheathing grades b. APA Rated Sturd-I-Floo ...

The arm abcd of the industrial robot lies in a vertical

The arm ABCD of the industrial robot lies in a vertical plane that is inclined at 40? to the yz-plane. The arm CD makes an angle of 30? with the vertical. A socket wrench attached at point D applies a 52-lb · ft couple a ...

Regarding the calculation of stresses in wood structural

Regarding the calculation of stresses in wood structural panels, a. What is the effective section modulus KS, and when is it used? b. What is shear through the thickness? c. What is rolling shear?

Ben bitdiddle is exploring finite-state machines of the

Ben Bitdiddle is exploring finite-state machines of the following form: A. Draw a state-transition diagram for the FS . Assume that you start in the state Q0 = 0, output = 1. B. Assume that you start in the state Q0 = 0, ...

An n-bit updown counter is a sequential circuit with a

An N-bit up/down counter is a sequential circuit with a clock input and an up/down control input. Wen control is 1, the circuit counts up, modulo 2N, on each rising edge of the clock. In other words, the present-state ou ...

1 briefly describe what is meant by resawn glulam what

1. Briefly describe what is meant by resawn glulam. What range of sizes is listed in NDS Supplement Tables 1C and 1D for resawn glulam? 2. What is the most common type of lamination end-joint splice used in glulam member ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen