Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Develop the stress – strain diagram for mild steel and mark the key points over it.

2) describe the Bearing stress and the Crushing stress.

3) describe the meaning of Creep? describe several stages of the creep with suitable sketch.

4) describe the factor of safety for ductile material and brittle material.

5) Describe the “Stress Concentration”.

6) describe the term Resilience.

7) Describe the material specification for:

a) Fe400,

b) SG900/2,

c) 20Cr18Ni2

8) describe why taper is offered on the cotter?

9) describe the term Lever and Leverage.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912105

Have any Question? 


Related Questions in Mechanical Engineering

Whats the maximum proof strength in ksi of a j429 gr 8 bolt

What's the maximum proof strength (in ksi) of a J429 GR 8 bolt and that of an ASTM A490 bolt? What's the proof strength of a metric Class 10.9 bolt in MPa? What is the ultimate strength and the yield strength (in MPa) of ...

Calculate the pressure in bar that would be equivalent to

Calculate the pressure in bar that would be equivalent to the attractive force between the Na + and Cl - ions in a salt crystal, at a separation of 2.81 Å and approximating the area over which the force works to be 4.00A ...

Rework problem if the exit velocity profile is given bywhen

Rework Problem. if the exit velocity profile is given by when y is measure vertically from the center line of the water tunnel. Problem A two-dimensional object is placed in a 4-ft-wide water tunnel as shown. The upstrea ...

Calculate the total lift force on the arctic hut shown

Calculate the total lift force on the Arctic hut shown below as a function of the location of the opening. The lift force results from the difference between the inside pressure and the outside pressure. Assume potential ...

What is the difference between initial and residual preload

What is the difference between initial and residual preload? Typically, what percentage of the work we do with a torque wrench ends up as preload in an individual bolt? Is the preload mentioned above initial or residual ...

Confirm that in hydrogenic atoms the spin-orbit coupling

Confirm that in hydrogenic atoms, the spin-orbit coupling constant depends on n and l as in eqn 7.24 2.Calculate the spin-orbit coupling constant for a 2p-electron in a Slater-type atomic orbital, and evaluate it for the ...

Compute a reasonable torque for an as-received unlubricated

Compute a reasonable torque for an as-received, unlubricated 1/2 -32  = 4 SAE J429 GR 5 bolt in a nonsafety-related normal application ?  Compare your torque to that suggested in Appendix E ?  When estimating bolt tensio ...

A steel frame is fabricated with the cross section shown

A steel frame is fabricated with the cross section shown. The centered hole allows cables to be run up to equipment above. The frame supports a load P at a distance d from the centroid of the vertical beam. Bending of th ...

The dc beta rises with collector current due to the sns

The d.c. beta rises with collector current due to the SNS effect and drops due to high injection level in the best. Combine these two effects and obtain the condition at which the beta peaks. Use the simplest formulas de ...

1 how large as a fraction of the supported weight w must

1. How large (as a fraction of the supported weight W) must the weight w of the forearm and hand be to change the analysis done under the assumption of weightlessness? 2. What sort of simple measurement or experiment cou ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen