+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1: Describe the independent and dependent sources with the help of V-I characteristics.

problem 2: Differentiate between ideal and practical sources and draw their characteristics.

problem 3: A 25 ohms resistor is connected across a voltage source V (t) = 150 Sin ωt. Find out the current I (t) and the instantaneous power P(t) and as well the average power. Draw the relevant waveforms.

problem 4: A series RLC circuit with R= 4 ohms, L = 2mH and C = 500 micro-farads is carrying a current waveform as shown in figure below. Find out the voltage across each element and sketch each voltage to same time scale.

problem 5: Compute the power absorbed by each component in the circuit as shown in figure below:

problem 6: A pure inductance of 3 mH carries a current of the wave form shown in figure below. Sketch the waveform of V(t) and P(t). Find out the average value of power.

Electrical & Electronics, Engineering

• Category:- Electrical & Electronics
• Reference No.:- M93508

Have any Question?

## Related Questions in Electrical & Electronics

### 1 state maxwells equations for static fields ina integral

1. State Maxwell's equations for static fields in (a) integral form, and (b) differential form. 2. Discuss the classification of static fields with reference to subsets of Maxwell's equations. 3. Outline the steps involv ...

### 1what is an electric dipole how is its strength defined2

1.What is an electric dipole? How is its strength defined? 2. What are the different kinds of polarization in a dielectric? 3. What is the polarization vector? How is it related to the electric field intensity? 4. Discus ...

### Question 1 a road 300 m long is required to be illuminated

Question 1. A road 300 m long is required to be illuminated by providing 40W fluorescent lamps. The width of the road is 4m. Design a street lighting scheme for obtaining minimum level of illumination of 0.6 lux assuming ...

### Determine the head loss between stations 1 and 2 in

Determine the head loss between stations (1) and (2) in Problem. Problem:- Oil (sp. gr. = 0.8) flows smoothly through the circular reducing section shown at 3 ft 3  /s. If the entering and leaving velocity profiles are u ...

### 1 a synchronous alternator is supplying 09 pu power to the

(1) A synchronous alternator is supplying 0.9 p.u. power to the grid when a temporary three-phase short occurs on the interconnector. The power angle curves are:- Pre-fault = 2.0 sin(delta) During fault = 0.5 sin(delta) ...

### 1 what is the voltage reflection coefficient at the short

1. What is the voltage reflection coefficient at the short circuit for a short-circuited line? 2. Can the transmitted wave current at the junction between two transmission lines be greater than the incident wave current? ...

### Consider a pv array charging batteries for an off-the-grid

Consider a PV array charging batteries for an off-the-grid, stand-alone system near Boulder, Colorado You plan to run everything in the house on 120 V ac. a. Suppose the load is estimated to consist of the following 120 ...

### An ltic system impulse response is given by ht ut-ut - 1a

An LTIC system impulse response is given by h(t) = u(t)-u(t - 1). a. Determine the transfer function H(s). Using H(s), determine and plot the magnitude response |H(jω)|. Which type of filter most accurately describes the ...

### A vertical cylindrical tank closed at the bottom is

A vertical, cylindrical tank closed at the bottom is partially filled with an incompressible liquid. A cylindrical rod of diameter d i (less than tank diameter, d 0 ) is lowered into the liquid at a velocity V. Determine ...

### Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen