Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Q1. Describe the importance of sectoring in decreasing the co-channel interference.

Q2. If a total of 30 MHz of bandwidth is assigned to a particular FDD cellular telephone system that uses two 20 KHz simplex channels to give full duplex voice and control channels, find out the number of channels available per cell if a system employs:

a) Four-cell reuse
b) Seven-cell reuse
c) 12-cell reuse.

Q3. Compare and contrast the merits and demerits of CDMA with TDMA-FDMA.

Q4. Describe the functioning of the given protocols in the Bluetooth technology:

a) Cable Replacement Protocol
b) Telephony Control Protocol
c) Adopted Protocols

Q5. Describe the fundamental characteristics of Cellular IP. Illustrate its merits and demerits.

Q6. describe the importance and categorization of the tags in RFID systems.

Q7. prepare brief notes on the Location management requirements in cellular systems.

Q8. Describe the functioning of Network and Switching Subsystem (NSS) and its registers in the GSM cellular system.

Q9. Compare and contrast the borrowing channel allocation (BCA), fixed channel allocation (FCA) and dynamic channel allocation (DCA) schemes. Illustrate their usage in the real time applications.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910529

Have any Question? 


Related Questions in Electrical & Electronics

1 a rectangular block of concrete 3 ft times 3ft times 6 in

1. A rectangular block of concrete 3 ft × 3ft × 6 in. has its 6- in. side half buried at the bottom of a lake 23 ft deep. What force is required to lift the block free of the bottom? What force is required to maintain th ...

Determine the nyquist sampling rate and the nyquist

Determine the Nyquist sampling rate and the Nyquist sampling interval for the signals a. sinc 2 (100πt) b. 0.01 sinc 2 (100πt) c. sinc(100πt) + 3 sinc 2 (60πt) d. sinc(50πt) sinc (100πt)

1 how is the magnetic flux density defined in terms of

1. How is the magnetic flux density defined in terms of force on a current element? 2. How is the magnetic flux density defined in terms of force on a moving charge? 3. What are the units of the magnetic flux density? 4. ...

1 consider a router that receives packets from three

1. Consider a router that receives packets from three different sources of traffic, each ranked in order of priorities (source 1 has highest priority -class 1, source 2 has class 2 priority and finally source 3 has lowes ...

1 in dictionary coding if there are 60 characters in the

1. In dictionary coding, if there are 60 characters in the message, how many times is the loop in the compression algorithm iterated? Explain. 2. In dictionary coding, should all dictionary entries that are created in th ...

1 how do you find the work done in moving a test charge by

1. How do you find the work done in moving a test charge by an infinitesimal distance in an electric field? 2. What is the amount of work involved in moving a test charge normal to the electric field? 3. What is the phys ...

Solve problem using force equilibrium ie internal force

Solve Problem using force equilibrium; i.e., internal force caused by stress is equal to external force. Problem A force F is applied at the tip of the uniform bar element shown in the figure. The initial length and the ...

For the structure of figure 610 continue the analysis

For the structure of Figure 6.10, continue the analysis beyond the quasistatic extension to obtain the input impedance correct to the third power in . Determine the equivalent circuit.

1 state faradays law in differential form for the general

1. State Faraday's law in differential form for the general case of an arbitrary electric field. How is it derived from its integral form? 2. What is meant by the net right-lateral differential of the x- and y-components ...

Below is the governing differential equation of

Below is the governing differential equation of one-dimensional bar under uniformly distributed load. Using one bar element, calculate the displacement at x = L and x = 1/2L. Compare these displacements with that of the ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro