Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

1. prepare a detailed note on Dry Process of Cement Manufacture.

2. Describe creep of concrete in detail.

3. prepare in detail about the effect of aggregates on workability of concrete.

4. Describe the various kinds of fibers used for reinforcing concrete.

5. prepare down the applications of Ferro cement.

6. Describe bacterial concrete in detail.

7. Describe the Hydration Process of Ordinary Portland  Cementin detail.

8. describe about the Classification of Aggregates in detail.

9. describe in detail about the factors which influence the choice of mix proportions.

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M913461

Have any Question? 


Related Questions in Civil Engineering

The step response of a linear circuit isa is the circuit a

The step response of a linear circuit is (a) Is the circuit a low-pass, high-pass, bandpass, or bandstop filter? (b) Construct the straight-line Bode gain plot and estimate the cutoff frequency and passband gain. (c) Use ...

1 describe the construction of underlayment-grade plywood

1. Describe the construction of UNDERLAYMENT-grade plywood. How is it used in floor construction? 2. A single-layer floor system is used to support a floor dead load of 10 psf and a floor live load of 75 psf. Panels with ...

The door header in fig 7c supports a dead load of 120 lbft

The door header in Fig. 7.C supports a dead load of 120 lb/ft and a roof live load of 120 lb/ft. Lumber is No. 2 Hem-Fir. C M = 1.0, C t = 1.0, and C i = 1.0. There are no bolt holes at the point of maximum moment. Later ...

A worker applies the forces p -10i 8j lb and q 10i lb to

A worker applies the forces P = -10i + 8j lb and Q = 10i lb to the handgrips of the electric drill. These forces are equivalent to the force R = 8j lb acting at the tip of the drill and the couple C R = -120j lb · in. De ...

Repeat problem p109 but use the numerals 1 2 and 4 instead

Repeat Problem P10.9, but use the numerals "1", "2" and "4", instead of the letters "T", "G" and "F". Test the trained network on each reference pattern and on noisy patterns. Discuss the sensitivity of the network. (Use ...

Consider the gain plot in figure p12-68a find the transfer

Consider the gain plot in Figure P12-68. (a) Find the transfer function corresponding to the straightline gain plot. (b) Use MATLAB to plot the Bode magnitude of the transfer function. (c) Design a circuit that will real ...

We want to design a perceptron network to output a 1 when

We want to design a perceptron network to output a 1 when either of these two vectors are input to the network: and to output a -1 when either of the following vectors are input to the network: i. Find and sketch a decis ...

This problem concerns a traffic light placed on a stretch

This problem concerns a traffic light placed on a stretch of road where there is no cross traffic, but where pedestrians often cross. There are two sets of lights, one facing each direction of traffic, and two pedestrian ...

1 regarding the overturning of a shearwall describe the

1. Regarding the overturning of a shearwall, describe the possible vertical soil bearing pressure diagrams. Give the formulas that are used to obtain the maximum soil pressure for the two distributions. 2. Refer to Fig. ...

The flexible shaft ab of the wrench is bent into a

The flexible shaft AB of the wrench is bent into a horizontal arc with a radius of 24 in. The two 20-lb forces, which are parallel to the z-axis, are applied to the handle CD, as shown. Determine the combined moment of t ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro