Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

1) Describe the construction of pile foundation and Caissons with neat and suitable sketches.

2) prepare down the method of improving bearing capacity of soils.

3) prepare down the different methods adopted to make a building damp proof.

4) prepare down the different kinds of bonds in bricks work? Describe 1 brick thick wall and 11/2 brick thick wall in English bond.

5) Describe different kinds of pitched roofs with sketches.

6) prepare a detailed note on floor finishing suited for the following: (i) ware house (ii) Hospital (iii) Library.

7) Plan a stair case for a residential building in which vertical distance between each floor is 3.36m. The size of the stair hall is limited to 4.5 m x 3m. Suppose any other relevant data.

8) prepare brief note on:

(i) Flush door

(ii) Revolving door

(iii) Casement window

(iv) Sash window

9)(a) prepare down the general fire safety requirements adopted for buildings.

(b) prepare down the fire resisting properties of:

(i) Bricks

(ii) Concrete

(iii) Steel

10)(a) Describe how will you achieve thermal insulation of roofs.

(b) prepare down the general planning principles which are considered for good acoustical conditions of a hall.

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M913347

Have any Question? 


Related Questions in Civil Engineering

1 design a light weight truss of steel or

1. Design a light weight truss of steel or aluminiumadnodized material of 2. Cantilever Span - 15 m with a load of 800 kg on the free end pl

Consider the two classes of patterns that are shown in

Consider the two classes of patterns that are shown in Figure P11.1. Class I represents vertical lines and Class II represents horizontal lines. i. Are these categories linearly separable? ii. Design a multilayer network ...

Te forces p and q act on the handles of the wrench if p

The forces P and Q act on the handles of the wrench. If P = 32 lb and Q = 36 lb, determine the combined moment of the two forces about the z-axis.

The flexible shaft ab of the wrench is bent into a

The flexible shaft AB of the wrench is bent into a horizontal arc with a radius of 24 in. The two 20-lb forces, which are parallel to the z-axis, are applied to the handle CD, as shown. Determine the combined moment of t ...

Suppose we wish to measure the traffic at a point on a

Suppose we wish to measure the traffic at a point on a railroad track, counting the axle crossings in each direction. We set up a light beam just above the rails and place two photocells A and B some inches apart, as sho ...

A couple of magnitude 360 lb middot ft is applied about

A couple of magnitude 360 lb · ft is applied about portion AB of the drive shaft (the drive shaft is connected by universal joints at points B and C). Compute the moment of the applied couple about the portion CD when th ...

The drag on a 2-m-diameter satellite dish due to an 80 kmh

The drag on a 2-m-diameter satellite dish due to an 80 km/h wind is to be determined through wind tunnel testing on a geometrically similar 0.4-m-diameter model dish. a. At what air speed should the model test be perform ...

Question if y1 and y2 are alternate depths of a rectangular

Question: If y 1 and y 2 are alternate depths of a rectangular channel show that y c  → Criticle depth 2y 1 ²y 2 ²/(y 1 +y 2 ) = Y c 3 and hence the specific energy, E = (y 1 2 + y 1 y 2 +y 2 2 )/(y 1 + y 2 ) No of Pages ...

Suppose that we have the following three reference patterns

Suppose that we have the following three reference patterns and their targets: Each pattern is equally likely. i. Draw the network diagram for an ADALINE network with no bias that could be trained on these patterns. ii. ...

Write data analysis methods of aac autoclaved aerated

Write Data analysis methods of AAC (Autoclaved aerated concrete) in Oman. Attachment:- sample.rar

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen