Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Describe the construction and working principle of Transformer?

problem 2: Derive an emf equation of a single phase transformer. The maximum flux density in the core of 250/3000 volts, 50 Hz single phase transformer is 1.2 Weber per square meter. If the emf per turn is 8 volts, then find out the primary and secondary turns and area of the core.

problem 3: The primary winding of a 50 Hz single phase transformer has 480 turns and fed from 6400 v supply. The secondary winding has 20 turns. Find out the peak value of flux in the core and the secondary voltage.

problem 4: What are the various functions of a transformer?

problem 5: Derive an expression for the voltage per turn of a transformer.

problem 6: What are the different losses taking place in a transformer on load? How can such losses be found out experimentally?

problem 7: Define the term voltage regulation of a transformer. Deduce the expression for the voltage regulation.

problem 8: The number of turns on the primary and secondary windings of a single phase transformer is 350 and 35 correspondingly. If the primary is connected to a 2.2 kV, 50 Hz supply, and then find out the secondary voltage. 

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M93244

Have any Question? 


Related Questions in Electrical & Electronics

A a signal x t 5 sinc2 5pit cos 20pit is sampled at a

a. A signal x (t) = 5 sinc 2 (5πt) + cos 20πt is sampled at a rate of 10 Hz. Find the spectrum of the sampled signal. Can x (t) be reconstructed by lowpass filtering the sampled signal? b. Repeat part (a) for a sampling ...

Suppose that a discrete-time system is specified by the

Suppose that a discrete-time system is specified by the transfer function Compute and plot a. The step response of the system b. The impulse response of the system c. The response of the system to the input signal

1 what is snells law2 what is meant by the plane of

1. What is Snell's law? 2. What is meant by the plane of incidence? Distinguish between the two different linear polarizations pertinent to the derivation of the reflection and transmission coefficients for oblique incid ...

1 in one-dimensional dct if n 1 the matrix transformation

1. In one-dimensional DCT, if N = 1, the matrix transformation is changed to simple multiplication. In other words, M = T × p, in which T, p, and M are numbers (scalar value) instead of matrices. What is the value of T i ...

1 state maxwells equations for static fields ina integral

1. State Maxwell's equations for static fields in (a) integral form, and (b) differential form. 2. Discuss the classification of static fields with reference to subsets of Maxwell's equations. 3. Outline the steps involv ...

1 consider three equally spaced sources of strength m

1. Consider three equally spaced sources of strength m placed at (x, y) = ( a, 0),(0, 0), and (a, 0). Sketch the resulting streamline pattern. Are there any stagnation points? 2. Sketch the streamlines and potential line ...

Discretize the continuous-time system with transfer

Discretize the continuous-time system with transfer function H(s) = (s + 10 )/s with use of the bilinear (Tustin) approximation method. Verify your result by converting the computed discrete-time system to continuous-tim ...

A the highest frequency in the spectrum x omega fig p81-8a

a. The highest frequency in the spectrum X (ω) (Fig. P8.1-8a) of a bandpass signal x (t) is 30 Hz. Hence, the minimum sampling frequency needed to sample x (t) is 60 Hz. Show the spectrum of the signal sampled at a rate ...

1 what is the propagation vector interpret the significance

1. What is the propagation vector? Interpret the significance of its magnitude and direction. 2. Discuss how the phase constants along the coordinate axes are less than the phase constant along the direction of propagati ...

1 oil is supplied at the center of two long plates the

1. Oil is supplied at the center of two long plates. The volumetric flow rate per unit length is Q and the plates remain a constant distance, b, apart. Determine the vertical force per unit length as a function of the Q, ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen