Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1) What do you mean by interfacing?

problem 2) Describe the concept of Direct Memory Access (DMA) in detail.

problem 3) Describe the functions of Handshake signals in detail.

problem 4) Describe what SIM is. describe the bit pattern of an accumulator for SIM instruction.

problem 5) prepare down the operating modes of the 8155A programmable device.

problem 6) prepare a detailed note on any of the applications of microprocessors.

problem 7) Describe the DMA controller 8257?

problem 8) Sketch the block diagram of 8255 and describe it’s working. What do you mean by Control Word? Find out the control word for the configuration of 8255 given below:-

Port A – Output
Mode of port A – Mode 1
Port B – Output
Mode of port B – Mode 0
Port C lower (pins PC0 – PC2) – Output

problem 9) What do you mean by 8254? Describe its different operating modes. prepare down its areas of applications.

problem 10) Describe main components of 8259 with the help of appropriate diagram.

problem 11) Describe USART in detail.

problem 12) Describe the functional diagram of keyboard and display controller in detail.

problem 13) Describe the functional diagram of 8155 and describe its control word in detail.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99219

Have any Question? 


Related Questions in Electrical & Electronics

1 what is a poynting vector what is its physical

1. What is a Poynting vector? What is its physical significance? 2. What is the physical interpretation of the surface integral of the Poynting vector over a closed surface? 3. Discuss how the fields far from a physical ...

1 how do you find the exact value of the line integral2

1. How do you find the exact value of the line integral? 2. What is the physical significance of the line integral of the earth's gravitational field intensity? 3. What is the value of the line integral of the earth's gr ...

Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

A clean 15--efficient module stc 1 m2 in size has its own

A clean, 15-%-efficient module (STC), 1 m 2 in size, has its own 90% efficient inverter. Its NOCT is 44° C and its rated power degrades by 0.5%/° C above the 25° C STC. a. What would its STC rated power be? b. Find the k ...

If the shock-wave velocity in problem is approximated by

If the shock-wave velocity in Problem is approximated by the speed of sound, determine the pressure change causing a velocity change of 10 fps in (a) air at standard conditions; (b) water. Problem:- The shock wave illust ...

Determine the maximum film velocity in problemproblem

Determine the maximum film velocity in Problem. Problem Aviscous film drains uniformly down the side of a vertical rod of radius R. At some distance down the rod, the film approaches a terminal or fully developed flow su ...

1 a 16-scale model of a torpedo is tested in a water tunnel

1. A 1/6-scale model of a torpedo is tested in a water tunnel to determine drag characteristics. What model velocity corresponds to a torpedo velocity of 20 knots? If the model resistance is 10 lb, what is the prototype ...

Suppose that a discrete-time system is specified by the

Suppose that a discrete-time system is specified by the transfer function Compute and plot a. The step response of the system b. The impulse response of the system c. The response of the system to the input signal

1 complete the missing steps in the evaluation of the

1. Complete the missing steps in the evaluation of the integral in equation (9.39a). 2. Find the time-average power required to be radiated by a half-wave dipole in order to produce an electric field intensity of peak am ...

1 two immiscible fluids of different density and viscosity

1. Two immiscible fluids of different density and viscosity are flowing between two parallel plates. Express the boundary conditions at the interface between the two fluids. 2. Determine the velocity profile for fluid fl ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro