+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1: describe the measuring tools and systems in detail.

problem 2: Describe in detail the procedure for inspection of steering system.

problem 3: prepare brief notes on:

a) Detonation.
b) Overheating of Engines.

problem 4: Describe the common troubles in the transmission system and prepare down all the appropriate remedies.

problem 5: prepare in detail procedure of trouble shooting in suspension system.

problem 6: prepare short notes on:

a) Wheel Pulling.
b) Tyre wears.
c) Wobbling.
d) Poor Returnability.

problem 7: prepare brief notes on service information and manual types?

problem 8: Describe the detail procedure of trouble shooting of chassis lubrication.

problem 9: prepare brief notes on:

a) Slipping.
b) Dragging.
c) Vibration.
d) Hard shifting

problem 10:

a) Describe how a battery must be maintained.
b) prepare brief notes on Wheel Balancing.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M93142

Have any Question?

## Related Questions in Mechanical Engineering

### 1 what is a design inequality2 how is the usual design

1. What is a design inequality? 2. How is the usual design inequality modified to account for statistical variability? 3. What is a load factor? A load effect? A resistance factor? 4. What is a limit-states design?

### Project solve the 3-dimensional steady state heat transfer

PROJECT Solve the 3-dimensional, steady state heat transfer problem for a cartesian system either numerically or analytically. - If you use the numerical method, write a computer code using the finite difference method o ...

### A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

### This atomic force microscope probe is a silicon beam and

This atomic force microscope probe is a silicon beam and tip. The beam is 40 µm wide, 4 µm thick, and 130 µm long. The tip is set back 15 µm from the end of the cantilever. The deflection of the tip is 1 µm for every 42 ...

### What do we mean by the term torque reaction a right angle

What do we mean by the term torque reaction? A right angle nut runner is used to produce 500 ft-lb of torque on a bolt having a 7/8 -9 UNC thread. The tool is 18 in. long. How much reaction force, created by the reaction ...

### 1 the v-shaped tank has width w into the paper and is

1. The V-shaped tank has width w into the paper and is filled from the inlet pipe at volume flow Q. Derive expressions for (a) the rate of change dh/dt and (b) the time required for the surface to rise from h 1  to h 2 . ...

### In order to penetrate a workpiece a tungsten carbide drill

In order to penetrate a workpiece, a tungsten carbide drill bit is subject to a torque of 3.8 Nm and an axial force of 5 kN. Tungsten carbide is very strong (compressive strength 1400 MPa, tensile strength 340 MPa) but a ...

### Asignmentnote all dimensions are in mm unless stated

ASSIGNMENT Note: All dimensions are in mm unless stated otherwise. A steel frame is shown in Figure 1. The steel used is ASTM A572 Grade 50. It consists of two span and braced by an arrangement of trusses at the right si ...

### The maximum theoretical efficiency of an internal

The maximum theoretical efficiency of an internal combustion engine is achieved in a reversible Carnot cycle. Assume that the engine is operating in the Otto cycle and that = 5R/2 for the fuel-air mixture initially at 27 ...

### Equipment engineering and design structural failure

Equipment Engineering and Design Structural Failure Problem- Background - A 6 ton pressure vessel - see dimensioned drawing - was being lowered onto a "stillage"or temporary supporting structure for testing outside a fac ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen