Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. Describe the process of electrical discharge machining, its process parameters and applications.

2. describe the wire cut EDM equipment, its working, applications and advantages in detail.

3.(i) With the help of neat and suitable sketch, describe the EDM process. In detail

(ii) What are the advantages of wire EDM process?

4.(i) Describe the classification and characteristics of different spark erosion generators.

(ii) With help of neat and suitable sketch describe the mechanism of material removal in EDM.

5.(i) Describe the working principle, elements and characteristics of wire EDM in detail.

(ii) Describe how stratified wire works. Also describe about recent developments in wire EDM.

6. prepare down the factors which influence oxidation in ECM.

7. prepare down the materials used to make the tool electrode.

8. prepare down the main functions of electrolysis in the ECM.

9. prepare down the properties are expected from electrolysis used in the ECM.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911710

Have any Question? 


Related Questions in Mechanical Engineering

A beam with a rectangular cross section has dimensions as

A beam with a rectangular cross section has dimensions, as defined in Fig. 8.13, of b = 40and t = 10 mm. The beam is made of 7475-T7351 aluminum and is subjected to a bendingmoment of M = 900 N·m. (a) If a through-thickn ...

The velocity profile in the annular control volume of

The velocity profile in the annular control volume of Example is approximately linear, varying from a velocity of zero at the outer boundary to a value of ωd/2 at the inner boundary. Develop an expression for the fluid v ...

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

1 a pressure of 10 mpa is applied to 025 m3nbspof a liquid

1. A pressure of 10 MPa is applied to 0.25 m 3  of a liquid, causing a volume reduction of 0.005 m 3 . Determine the bulk modulus of elasticity. 2. The bulk modulus of elasticity for water is 2.205 GPa. Determine the cha ...

Leaning polea pole of negligible mass leans against a wall

Leaning pole A pole of negligible mass leans against a wall, at angle ? with the horizontal. Gravity is directed down (a) Find the constraint relating the vertical acceleration of one end to the horizontal acceleration o ...

Imagine a set of three n2 molecules frozen in a crystal so

Imagine a set of three N2 molecules frozen in a crystal so that no rotation or translation can occur. But there is energy in vibration, which totals E = 3ve , where the vibrational constant e = 2358cm-1 . If we apply the ...

Extend the analyses of the three narrow-gate effects to

Extend the analyses of the three narrow-gate effects to include the voltage dependent bulk charge. Give two numerical examples using the submicron transistors of problem P685.5. Problem P685.5 Extend the analyses of the ...

1 a 1968 volkswagen sedan is driving over a 7300-ft-high

1. A 1968 Volkswagen sedan is driving over a 7300-ft-high mountain pass at a speed of v m/s into a headwind of W m/s. Compute the gage pressure in mPa at a point on the auto where the velocity relative to the auto is v - ...

As can often be seen in a kitchen sink when the faucet is

As can often be seen in a kitchen sink when the faucet is running, a high-speed channel flow (v 1 , h 1 ) may ''jump'' to a low-speed, low-energy condition (v 2 , h 2 ). The pressure at sections 1 and 2 is approximately ...

1 what requirements control the derivation of load-stress

1. What requirements control the derivation of load-stress relations? 2. Describe the method of mechanics of materials. 3. How arc stress-strain-temperature relations for a material established? 4. Explain the difference ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen