Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Describe of the following process with neat sketches.

a) Hot Extrusion

b) Wire Drawing

2) Describe the following terms with suitable sketches.

a) Blanking and trimming

b) Electro hydraulic forming

3) describe the plasma arc welding process and specify its different application advantages and limitations.

4) prepare a brief note on the following term:

a) Thermit welding

b) Brazing

c) Defects in welding

5) a) Describe significant characteristics of the Moulding sand.

b) describe the core making process with appropriate exs.

6) Discuss about the Investment casting and also specify its application and limitations in detail.

7) Describe the several types of grinders with required sketches.

8) Describe the following processes with essential sketches.

a) Super finishing

b) Metal spraying

9) Describe with appropriate ex for selective laser sintering and specify its benefits and limitations.

10) describe the working principle of stereo–lithography and also specify the benefits and application of this process.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913438

Have any Question? 


Related Questions in Mechanical Engineering

At the end of a water pipe of 3-in diameter is a nozzle

At the end of a water pipe of 3-in. diameter is a nozzle that discharges a jet having a diameter of 1½ in. into the open atmosphere. The pressure in the pipe is 60 psig (pounds per square inch gage), and the rate of disc ...

Figure a shows a steel i-beam cross section note not

Figure (a) shows a steel I-beam cross section (note, not symmetric about the y axis). Two steel plates with cross section 10 mm × 200 mm are welded to the beam. Figure (b) and the 3D inset show the configuration of the c ...

Part 1 key engineering terms fill in the blanks -1

Part 1 Key Engineering Terms: fill in the blanks - 1. Phase: a _____________________________________ homogeneous and distinct portion of material system. 2. Degrees of freedom: number of variables that can be changed ___ ...

A linear spring k is to be designed to stop a 20-mg

a linear spring k is to be designed to stop a 20-mg railroad car traveling at 8km/h within 400 mm after impact. Find the smallest value of k that will produce the desired result.

Problem -a piston at one end of a gas filled circular tube

Problem - A piston at one end of a gas filled circular tube of area S oscillates with real-valued velocity: U p (t) = U 1 cos(ω 1 t) + U 2 sin(ω 2 t) Note that two oscillation frequencies are present. The other end of th ...

1 sketch the deformation of a fluid element for the

1. Sketch the deformation of a fluid element for the following cases: 2. For a two-dimensional, incompressible flow with velocity v x  = v x (y), sketch a three-dimensional fluid element and illustrate the magnitude, dir ...

Define prying action sketch an alternative joint diagram

Define prying action? Sketch an alternative joint diagram showing the effects of prying action Name at least two things the joint designer can do to reduce prying action? This and the following three questions are all in ...

It has been observed that the most effective way to crush

It has been observed that the most effective way to crush an empty aluminum beverage can is to apply an eccentric compressive load. Use buckling theory to explain this phenomenon. The can wall thickness is 80 μm, and the ...

The space between two very long parallel plates separated

The space between two very long parallel plates separated by a distance h is filled with a fluid with viscosity where μ0 is a constant and n is a constant exponent. The top plate slides to the right with a constant speed ...

Please reference any source of outside information as

Please reference any source of outside information as needed to answer these questions. 1. In a frozen food plant, atmospheric air is to go through a pre-cooler to be partially dehydrated so that during its passage throu ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro