Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) prepare a short note on low cost automation.

problem 2) What are programmable logic controllers? Describe the applications for which these are used. Describe important advantages and disadvantages.

problem 3) Describe the various types of sensors used in robotics.

problem 4) Describe sequential control of cylinders.

problem 5) What are solid state switches? prepare down its applications

problem 6) With the help of neat sketches, describe the working of (a) vane pump (b) check valve

problem 7) Describe the different configurations of Robots with and well labelled sketch and give their respective work volumes.

problem 8) prepare brief note on the following:

a) Stepper motor.

b) Welding operation

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98956

Have any Question? 


Related Questions in Mechanical Engineering

A uniform cantilever beam with triangular cross section is

A uniform cantilever beam with triangular cross section is loaded only due to its own weight (a load uniformly distributed along the length). What is the ratio of the maximum tensile normal stress to the maximum compress ...

1 estimate the viscosity of nitrogen at 175 k using given

1. Estimate the viscosity of nitrogen at 175 K using given equation. 2. Calculate the viscosity of oxygen at 350°K and compare with the value given in Appendix I. 3. What is the percentage change in the viscosity of wate ...

1 water is flowing through a large circular conduit with a

1. Water is flowing through a large circular conduit with a velocity profile given by the equation v = 9(1- r 2 /16) fps. What is the average water velocity in the 1.5-ft pipe? 2. Water enters a 4-in. square channel as s ...

Calculate the power factor of an electronic system subject

Calculate the power factor of an electronic system subject to a reasonable amount of harmonics given as THD(v) = 1.0%, the displacement factor is 0.92. What would be the calculated error if harmonic components were not t ...

A cylindrical pressure vessel of 120 in outside diameter

A cylindrical pressure vessel of 120 in outside diameter, used for processing rubber, is 36 ft long. If the cylindrical portion of the vessel is made from 1 in thick steel (E = 29 × 10 6 psi, ν = 0.25) plate and the vess ...

Problem -a consider a one-component system consisting of

Problem - a. Consider a one-component system consisting of spherical bubbles of vapor inside a liquid, which is commonly observed as a liquid begins to boil. This is similar to the case considered in class in which liqui ...

List three ways to control preload directly what are the

List three ways to control preload directly ? What are the advantages of a bonded ultrasonic transducer? What is sometimes cited as a disadvantage? Can torque be used to tighten a 6 in. diameter bolt? If not, why not? Na ...

How do bolt stiffness and joint stiffness affect the angle

How do bolt stiffness and joint stiffness affect the angle of turn versus preload relationship? A rubber washer has been used instead of a metal one, by mistake. How will preload be affected if the same predetermined tor ...

An aluminum e 70 gpa cantilever must carry an end load of

An aluminum (E = 70 GPa) cantilever must carry an end load of 1.4 kN as shown. However, in this design, when the beam is loaded the end of the cantilever A has to have the same elevation as point C (i.e., the net deflect ...

Problem -an aluminum extrusion was created in the shape at

Problem - An aluminum extrusion was created in the shape at the right as shown with the origin at the lower left corner. Show all work in finding the centroid (4). Find moments of inertia with respect to the x and y axes ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen