Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) Describe basic structure and working of pressure relief and time delay valve in detail.

problem 2) Describe different logic functions used in PLC.

problem 3) Describe classification of robots based on geometry and path movement in detail.

problem 4) What are Robotic End-effectors? prepare down its kinds and applications.

problem 5) Describe with appropriate diagram the function of Teach Pendant Box.

problem 6) Describe different kinds of Electrical Actuation Systems?

problem 7) Describe the applications of Industrial Robots in welding, assembling and spray painting.

problem 8) Describe the applications of Personal Computers in various control and automation function.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98961

Have any Question? 


Related Questions in Mechanical Engineering

It has been observed that the most effective way to crush

It has been observed that the most effective way to crush an empty aluminum beverage can is to apply an eccentric compressive load. Use buckling theory to explain this phenomenon. The can wall thickness is 80 μm, and the ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

The figure illustrates the operation of an air lift pump

The figure illustrates the operation of an air lift pump. Compressed air is forced into a perforated chamber to mix with the water so that the specific gravity of the air-water mixture above the air inlet is 0.5. Neglect ...

It is desired to use a 075-m diameter beach ball to stop a

It is desired to use a 0.75-m diameter beach ball to stop a drain in a swimming pool. Obtain an expression that relates the drain diameter D and the minimum water depth h for which the ball will remain in place.

One excited state of the sodium atom lies at 25 73986 cm1

One excited state of the sodium atom lies at 25 739.86 cm1 above the ground state, another lies at 50 266.88 cm-1 . Suppose they are connected by a perturbation equivalent in energy to (a) 100 cm -1 , (b) 1000 cm -1 , (c ...

Some experimental data for shearing stress tau and shear

Some experimental data for shearing stress τ and shear strain rate γ obtained for a particular non-Newtonian fluid at 80?F are shown below. Please plot these data and fit a second-order polynomial to the data using graph ...

Health and safety management 1 the following gas

Health and Safety Management 1. The following gas detector tubes are available for direct reading of concentrations of the toxic gas hydrogen sulfide Tube Concentration 4HT 1-40% 4HH 0.1-4.0% 4H 10-3200 ppm 4M 12.5-500 p ...

In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

Gas turbine engines are mostly seen in aircraft while

Gas turbine engines are mostly seen in aircraft, while piston combustion engines are mostly seen in ground vehicles. Which advantages and disadvantages of these engines have caused them to be favorable for their respecti ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro