Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. Describe repair methods of conveyors in detail.

2. Describe the repair methods for crane and hydraulic lift.

3. Describe the equipment record in brief.

4. Describe job order system.

5. Describe different hydraulic and pneumatic equipments used in material handling purpose. Describe how to maintain it.

6. Describe the maintenance procedure for different small equipment for material handling purpose like chain block, chain, rope, trolley and R.G.B.

7. prepare down the advantages of CMMS.

8. What do you mean by work order systems?

9. Describe the role of equipment records in maintenance.

10. What are the benefits of job card system.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911619

Have any Question? 


Related Questions in Mechanical Engineering

1 a glass bulb of volume 0198 l contains 0457 g of gas at

1. A glass bulb of volume 0.198 L contains 0.457 g of gas at 759.0 Torr and 134.0°C. What is the molar mass of the gas? 2. A 455 cm 3 vessel contains a mixture of Ar and Xe. If the mass of the gas mixture is 2.245 g at 2 ...

1 the deepest known point in the ocean is 11034 m in the

1. The deepest known point in the ocean is 11,034 m in the Mariana Trench in the Pacific. Assuming sea water to have a constant density of 1050 kg/m 3 , determine the pressure at this point in atmospheres. 2. Determine t ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

The viscosity eta of water at various temperatures t is

The viscosity η of water at various temperatures T is given in the following table Compute the cubic splines that pass through the three given points. Evaluate the viscosity at 25°C. The measured value has been reported ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

Determine the maximum in-plane stresses for a cylindrical

Determine the maximum in-plane stresses for a cylindrical tank made of steel (E = 205 GPa, ν = 0.30), having a mean radius of 2 m and a thickness of 20 mm, and subjected to an internal pressure p = 1 MPa.

For the bar in problem 1112 find the largest allowable

For the bar in Problem 11.12, find the largest allowable value of P if the allowable compressive stress is 250 MPa. Problem 11.12: A steel bar with the cross section shown and effective length L = 2.5 m is subjected to a ...

A neighborhood fuel cell power plant is to be designed for

A neighborhood fuel cell power plant is to be designed for an electric power output of 2000 kW with liquid-water product. Estimate the flow rates of hydrogen and oxygen during peak power production, assuming an 80% effic ...

1 the circular gate abc has a 1 m radius and is hinged at b

1. The circular gate ABC has a 1 m radius and is hinged at B. Neglecting atmospheric pressure, determine the force P just sufficient to keep the gate from opening when h = 12 m. 2. The figure below shows an open triangul ...

Health and safety management 1 the following gas

Health and Safety Management 1. The following gas detector tubes are available for direct reading of concentrations of the toxic gas hydrogen sulfide Tube Concentration 4HT 1-40% 4HH 0.1-4.0% 4H 10-3200 ppm 4M 12.5-500 p ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro