Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

a) Describe any three devices which are used for high pressure measurement with proper diagrams.
b) Describe the principle of turbine type flow meter and Rotameter with easy sketches.

problem 2:

a) Describe the measurement of diesel flow in diesel engine power plant.
b) How do you measure power generated in diesel power plant?

problem 3: Describe any three devices which are used to measure the temperature with diagrams.

problem 4: Describe the various measurements and instruments used in the hydroelectric power plant.

problem 5:

a) describe the working of Gas chromatograph with appropriate sketch.
b) describe the salient features of Non Dispersive Infra Red (NDIR) Analyzer with diagram.

problem 6:

a) describe the detailed manner of measuring gas flow in gas turbine power plant.
b) Describe the vibration measurement and instruments used for that in gas turbine power plant.

problem 7: describe with neat sketches, the working principle of Flame Ionization Detector (FID) and smoke meter.

problem 8: describe the Hot-Wire and Hot-film Anemometer with appropriate sketches.

problem 9: Describe the application of optical pyrometer and Heat flux meter.

problem 10:

a) Describe the details of safety instruments which are used in nuclear power plant.
b) Derive an expression to compute the co-efficient of discharge in a Venturimeter.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93149
  • Price:- $100

Priced at Now at $100, Verified Solution

Have any Question? 


Related Questions in Mechanical Engineering

The fugacity and fugacity coefficient are determined as a

The fugacity and fugacity coefficient are determined as a function of pressure and temperature for a model gas. These variables can be varied using sliders. The student is asked to determine the Boyle temperature and als ...

Name several factors that can lead to a change in clamping

Name several factors that can lead to a change in clamping force in an assembled joint ? Name at least three sources of bolting standards ? Three different tensile strengths are given for many bolt materials. Name them ? ...

1 if the design load is 90 kn 20300 lbf what is the dead

1. If the design load is 90 kN (20,300 lbf), what is the dead load and what is the intensity of the dead load in the light of the live load calculation of Problem CS1.1? 2. Determine the specific weight of lightweight co ...

An aluminum e 70 gpa cantilever must carry an end load of

An aluminum (E = 70 GPa) cantilever must carry an end load of 1.4 kN as shown. However, in this design, when the beam is loaded the end of the cantilever A has to have the same elevation as point C (i.e., the net deflect ...

A cubical piece of wood with an edge l in length floats in

A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90. What moment M is required to hold the cube in the position shown? The right-hand edge of the block is flush ...

If in the system for problem the total drag on the object

If, in the system for Problem, the total drag on the object is measured to be 800 N/m of length normal to the direction of flow, and frictional forces at the walls are neglected, find the pressure difference between inle ...

1 develop three scenarios for comparable circular cylinders

1. Develop three scenarios for comparable circular cylinders of radius R and square tubes of side H that allow one to say R ∼ H. (Hint: What geometric attributes of the cylinder and tube might be made equal?) 2. If a str ...

A domestic food freezer maintains a temperature of - 15degc

A domestic food freezer maintains a temperature of - 15°C. The ambient air temperature is 30°C. If heat leaks into the freezer at the continuous rate of 1.75 kJ/s what is the least power necessary to pump this heat out c ...

If the speed of the shaft is doubled in given problem what

If the speed of the shaft is doubled in given Problem, what will be the percentage increase in the heat transferred from the bearing? Assume that the bearing remains at constant temperature. Problem An automobile cranksh ...

1 a vertical cylindrical tank having a base diameter of 10

1. A vertical cylindrical tank having a base diameter of 10 m and a height of 5 m is filled to the top with water at 20°C. How much water will overflow if the water is heated to 80°C? 2. A liquid in a cylinder has a volu ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen