Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. Describe the various kinds of GT Machine Cells with appropriate diagrams in detail.

2. Describe the problems related with traditional production planning and control.

3. prepare down the different output reports which can be generated by MRP program and prepare down the benefits of MRP?

4. Describe the basic components of the Direct Digital Control System.

5. Describe the factors that define the process requirements towards choice of particular machine(s) that make up a CIMS.

6. prepare brief notes on fundamentals of networking.

7. How production systems are categorised. Describe about each type briefly. Also, prepare down the objectives of a manufacturing system.

8. Describe about the Opitz and MICLASS systems of parts classification and coding in detail.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913342

Have any Question? 


Related Questions in Mechanical Engineering

1 a 1968 volkswagen sedan is driving over a 7300-ft-high

1. A 1968 Volkswagen sedan is driving over a 7300-ft-high mountain pass at a speed of v m/s into a headwind of W m/s. Compute the gage pressure in mPa at a point on the auto where the velocity relative to the auto is v - ...

If the kansas city building code specified that a floor

If the Kansas City Building Code specified that a floor structure must support a live load of 4.79 kPa (100 psf), and if the walkway length L = 9.1 m = 30.0 ft and width b = 2 m = 6.56 ft, what contribution is made to th ...

1 the hypodermic needle shown below contains a liquid serum

1. The hypodermic needle shown below contains a liquid serum (ρ = 1 g/cm 3 ). If the serum is to be injected steadily at 6 cm 3  /s, how fast should the plunger be advanced (a) if leakage in the plunger clearance is negl ...

Question 1 -1 plot the singular stress components sigmaxx

Question 1 - 1) Plot the singular stress components, σ xx , σ yy and τ xy for a cracked body under Mode I, Mode II and Mode III loading with a stress intensity factor K i = 10 MPa·m 1/2 (i = I, II and III). Plot the stre ...

The stepped shaft rotates at 120 rpm and has a 20 kw input

The stepped shaft rotates at 120 rpm and has a 20 kW input at A. 16 kW is taken off to operate machinery at B, and the remaining 4 kW is used at C. The shaft is stainless steel with yield strength in shear of 300 MPa. a. ...

Determine the effective moment and vertical shear force

Determine the effective moment and vertical shear force that would be required to replicate the effect of the three bar forces in Problem 1.15. Problem 1.15: For the truss shown, find the bar forces at the section indica ...

Two structural steel shafts with flanges forged on their

Two structural steel shafts with flanges forged on their ends are rigidly connected with a circle of bolts. The shafts are meant to rotate in their supports at A and D, however a 100 N · m torque is applied to flange B w ...

1 why are micropower plants so different from larger ones

1. Why are micropower plants so different from larger ones? In what cases are they recommended? 2. Discuss which of the conventional alternative sources of energy is more suitable for use with induction generators to pro ...

A small three-phase ig has the following nameplate data 110

A small three-phase IG has the following nameplate data: 110 V, 1.140 rpm, 60 Hz, Y connection, and 1250 W. The blocked rotor test at 60 Hz yielded the following: I = 69.4 A, P = 4200 W. The turn ratio between stator and ...

1 use simple classical particle kinetics to show that the

1. Use simple classical particle kinetics to show that the transvers electric field in the MOST is not a fundamental cause of mobility and drift velocity variation with the electric fields. 2. Find maximum oscillation fr ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro