Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1)(i) describe the chemistry involved in ECM process in detail.

(ii) Briefly describe about effect of high temperature and pressure of electrolyte on ECM process in detail.

(iii) Describe about the economics of ECM in detail.

2)(i) describe the working principle and elements of chemical machining. prepare down the factors on which the selection of the resist for use in chemical machining?

(ii) prepare down the specific advantages of using chemical machining over electrochemical machining? prepare down some of the practical applications of chemical machining process.

3)(i) Describe the principle of ECG with suitable sketch.

(ii) prepare down the advantage of EGC over conventional grinding.

(iii) prepare down the product application of ECG.

4) Describe in detail the ECM process with neat and suitable sketch and also prepare the advantages and application.

5)(i) Describe the process of electrochemical machining in detail.

(ii) Describe about the electrochecmical honing and electrochecmical grinding in detail.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911701

Have any Question? 


Related Questions in Mechanical Engineering

1 what requirements control the derivation of load-stress

1. What requirements control the derivation of load-stress relations? 2. Describe the method of mechanics of materials. 3. How arc stress-strain-temperature relations for a material established? 4. Explain the difference ...

It has been observed that the most effective way to crush

It has been observed that the most effective way to crush an empty aluminum beverage can is to apply an eccentric compressive load. Use buckling theory to explain this phenomenon. The can wall thickness is 80 μm, and the ...

Calculate the total lift force on the arctic hut shown

Calculate the total lift force on the Arctic hut shown below as a function of the location of the opening. The lift force results from the difference between the inside pressure and the outside pressure. Assume potential ...

1 at what temperature is the kinematic viscosity of

1. At what temperature is the kinematic viscosity of glycerin the same as the kinematic viscosity of helium? 2. According to the Hagen-Poiseuille laminar flow model, the volumetric flow rate is inversely proportional to ...

A closed rigid tank having a volume of 1 m3 contains a

A closed, rigid tank having a volume of 1 m 3 contains a mixture carbon dioxide (CO 2 ) and water vapor initially at 70°C and 200 kPa The mass of water vapor in the tank is 0.10 kg. The tank contents are cooled to 20°C. ...

1 the practical depth limit for a suited diver is about 185

1. The practical depth limit for a suited diver is about 185 m. What is the gage pressure in sea water at that depth? The specific gravity of sea water is 1.025. 2. Matter is attracted to the center of Earth with a force ...

Problem 1 -there is a circular combined open and closed

Problem 1 - There is a circular combined open and closed thin-walled section as shown in the figure. (R = 100mm, t = 2mm, S y = 100N) When shear force S y is applied to Web 24, calculate: a) Calculate I xx for the x-axis ...

The force applied to a nut in a nutcracker is larger than

The force applied to a nut in a nutcracker is larger than the force P applied to the handles. Model the top element of the nutcracker as a beam as shown, and find the forcce on the nut as a function of P and lengths a an ...

1 a square gate 4 m by 4 m is located on the 45deg face of

1. A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts. 2. ...

1 how large as a fraction of the supported weight w must

1. How large (as a fraction of the supported weight W) must the weight w of the forearm and hand be to change the analysis done under the assumption of weightlessness? 2. What sort of simple measurement or experiment cou ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro