Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Describe half adder and full adder in detail with suitable diagram.

2) Sketch a full adder and execute it by using logic gates.

3) prepare detailed notes on:

i) RS-flip flop

ii) D-flip flop

iii) JK -flip flop

iv) T-flip flop

v) JK-master slave flip flop

4) Describe the working of JK flip flop in detail.

5) Describe the operation of various types of shift register in detail.

6) Describe about Analog to Digital and Digital to Analog conversion in detail.

7) Describe the operation of RS flip-flop with logic diagram and truth table.

8) With essential diagrams describe the functioning of the following:

i) Decade counter

ii) D/A converter

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911952

Have any Question? 


Related Questions in Electrical & Electronics

Compute and plot the solution of the difference equation yn

Compute and plot the solution of the difference equation y[n] þ y[n 1] = 2x[n] þ x[n 1], where x[n] = 0.8n u[n] assuming zero initial conditions. Moreover, verify your answer (a) by examining if the derived solution sati ...

In communication channels transmitted signal is propagated

In communication channels, transmitted signal is propagated simultaneously by several paths of varying lengths. This causes the signal to reach the destination with varying time delays and varying gains. Such a system ge ...

Write the expression for the vector distance of a point in

Write the expression for the vector distance of a point in a rectangular room from one corner of the room, choosing the three edges meeting at that point as the coordinate axes. Describe the vector distance field associa ...

Term project - the step response of rlc circuitsthe team

Term Project - The Step Response of RLC Circuits The team project pertains to Chapter 9 in the text book. You should submit a single report and Multisim/ LTSpice file. The report should be submitted as a Word document an ...

Find the zero-state response yt of the network in fig p44-1

Find the zero-state response y(t) of the network in Fig. P4.4 -1 if the input voltage x(t) = te-tu(t). Find the transfer function relating the output y(t) to the input x(t). From the transfer function, write the differen ...

1 how do you find the approximate value of the surface

1. How do you find the approximate value of the surface integral over a given surface? 2. How do you find the exact value of the surface integral? 3. Provide physical interpretations for the closed surface integrals of a ...

1 implement the d latch to include an enable line using

1. Implement the D latch to include an enable line using Logisim. The enable line will be used to control when the D latch is set, so it is only set if the clock and enable line are high. 2. Implement the D latch to incl ...

Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

Question 1 a road 300 m long is required to be illuminated

Question 1. A road 300 m long is required to be illuminated by providing 40W fluorescent lamps. The width of the road is 4m. Design a street lighting scheme for obtaining minimum level of illumination of 0.6 lux assuming ...

An initially straight beam ab is bent into a circular arc

An initially straight beam AB is bent into a circular arc A'B' as shown in the figure. The deformation is specified as Where g(X 2 ) is a simple function of X 2 . (a) Find the deformation gradient in terms of g(X 2 ). (b ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen