Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1)(a) Describe briefly the programming languages used for computer aided structural analysis.

(b) describe the program modules for plane truss and grid.

problem 2)(a) describe the programme modules for space truss and space frames.

b)  describe briefly the process of transformation of coordinate system.

problem 3)a)  Describe briefly the various types of finite element models.

b)  describe the basic procedure in adopting FEM.

problem 4)a) prepare a computer program to evaluate member stiffness matrix in global axes of a plane frame element.

b) describe briefly the process of transformation of coordinate system.

problem 5) Describe briefly with a flowchart, about static analysis of one dimensional structure.

problem 6) prepare the algorithm for static analysis of any one one-dimensional structure.

problem 7) Describe in detail, the computer aided design of a one way slab.

problem 8) describe briefly the computer aided design of a singly reinforced RCC beam.

problem 9) Describe briefly the effect of soil-structure interaction on pipes.

problem 10) describe briefly the critical failure models of land sliding.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M97600

Have any Question? 


Related Questions in Mechanical Engineering

A closed cylindrical tank of length l radius r and wall

A closed cylindrical tank of length L, radius R, and wall thickness t contains a liquid at pressure p. If a hole is suddenly made in the cylinder, determine a. How much the tank radius R changes b. How much the tank leng ...

Determine the tip deflection of a beam with linear varying

Determine the tip deflection of a beam with linear varying width b(x), constant height h, length L, and elastic modulus E due to tip load P. Write the answer in terms of the maximum width b L = b(L). Also determine the n ...

Calculate the fraction of n2 molecules in a sample at 298 k

Calculate the fraction of N2 molecules in a sample at 298 K that have speeds less than 10.0ms -1 by integrating the Maxwell-Boltzmann distribution over the appropriate range of speeds (just writing the correct integral i ...

You are asked to design a cylindrical scuba tank with a

You are asked to design a cylindrical scuba tank with a radius R = 16 cm to a pressure of p = 12.0 MPa at a factor of safety of 2.0 with respect to the yield stress. The relevant tabulated yield values for the steel of w ...

1 by how much will the clamping force on the joint be

1. By how much will the clamping force on the joint be reduced? Sketch the new joint diagram, assuming maximum initial preload? Compute the estimated maximum bolt tension and minimum clamping force under the 3,000 lbs ex ...

A system and reservoir are in contact with each other he

A system and reservoir are in contact with each other. he volumes and numbers of particles are constant for both, and the overall energy of the universe is conserved. he degeneracy of the system obeys the equation ­ = AE ...

Describe the mil-std-1312 nas test name three generic ways

Describe the MIL-STD-1312 (NAS) test? Name three generic ways to prevent or at least minimize self-loosening? Define prevailing torque? A proper length-to-diameter ratio for the bolt can reduce or eliminate self-loosenin ...

Calculate the pressure in bar that would be equivalent to

Calculate the pressure in bar that would be equivalent to the attractive force between the Na + and Cl - ions in a salt crystal, at a separation of 2.81 Å and approximating the area over which the force works to be 4.00A ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

The maximum theoretical efficiency of an internal

The maximum theoretical efficiency of an internal combustion engine is achieved in a reversible Carnot cycle. Assume that the engine is operating in the Otto cycle and that = 5R/2 for the fuel-air mixture initially at 27 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro