Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: Derive the SFEE for the thermodynamic equipments such as:

a) Compressor.
b) Gas turbine.
c) Nozzle.
d) Condenser.

problem 2: What are the different modes of work and prepare brief notes on:

a) Shaft work.
b) Flow work.

problem 3: Air expands from 3 bar to 1 bar in a nozzle. The initial velocity is 90 m/s and temperature is 150oC. Estimate the final velocity. Cp = 1.005 kJ/kg K.

problem 4: prepare brief notes on:

a) Isobaric Process.
b) Adiabatic Process.

problem 5: Steam enters a turbine at a velocity of 12 m/s and specific enthalpy is 2960 kJ/kg. At the exit of the turbine, the steam velocity is 30 m/s and the specific enthalpy is 2400 kJ/kg. The heat lost throughout the flow via the turbine 20 kJ/kg and the steam flow rate is 85 kg/s. Find out the work output from the turbine.

problem 6: The parameters at inlet and exit of a nozzle are described below. Compute:

949_parameter of nozzle.jpg

a) Velocity of fluid at exit.
b) Rate of flow of fluid.
c) Area of the nozzle at the exit. Suppose the nozzle is horizontal and neglect the heat losses. 

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93720

Have any Question? 


Related Questions in Mechanical Engineering

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

Imagine a set of three n2 molecules frozen in a crystal so

Imagine a set of three N2 molecules frozen in a crystal so that no rotation or translation can occur. But there is energy in vibration, which totals E = 3ve , where the vibrational constant e = 2358cm-1 . If we apply the ...

Given the result of problem 67 estimate the magnitude of

Given the result of Problem 6.7, estimate the magnitude of the radial deflection of a pressurized cylinder as a fraction of its thickness Problem 6.7: Given that the hoop strain is likely to be a very small number, estim ...

The ground state 1s1 h atom has two hyperfine states f 0

The ground state 1s1 H atom has two hyperfine states, F = 0 and F = 1, which correspond to different relative orientations of the nuclear spin and electron spin. The transition between these two states has a wavelength o ...

Name the two types of bolted joints and tell why theyre

Name the two types of bolted joints and tell why they're called that? What is the main mission of the bolts in any joint? What factor largely determines the behavior and life of a tensile joint? Why are bolted joints oft ...

Name the principal modes of failure of both tensile and

Name the principal modes of failure of both tensile and shear joints? Describe or list the criteria a bolted joint designer must consider when selecting bolt size and material for a new joint? Will short, fat bolts gener ...

How is that process-that curve-modified if this is a sheet

How is that process-that curve-modified if this is a sheet metal joint? Do variations in friction between male and female threads affect the torque-turn relationship? Describe the turn-of-nut procedure used in structural ...

The figure illustrates the operation of an air lift pump

The figure illustrates the operation of an air lift pump. Compressed air is forced into a perforated chamber to mix with the water so that the specific gravity of the air-water mixture above the air inlet is 0.5. Neglect ...

A steel bar with the cross section shown and effective

A steel bar with the cross section shown and effective length L = 2.5 m is subjected to a compressive load P = 200 kN with a eccentricity e = 0.00625 m. Find (a) the beam's maximum deflection, and (b) the maximum normal ...

As discussed in section 11 new parameters are oten born out

As discussed in Section 1.1, new parameters are oten born out of the need to explain inconsistencies between experimental results and prevailing theory. In physics, mass is the property that determines the magnitude of t ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro