+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1)(a) Demonstrate five various types of lines used in engineering drawing giving their purpose.

(b) Print the following sentence in upper case, single stroke, and vertical letters in the ratio of 7:4. Take height of letters=12mm “TRUTH IS GOD”

problem 2)(a) With neat sketches, demonstrate how the following are dimensioned: Circles, holes chamfered surfaces, angles, curves.

(b) Draw the following systems of placing dimensions:

(i) Aligned system

(ii) Unidirectional system

problem 3) Construct a diagonal scale to read up to 1/10 of a mm, long enough to read up to 60mm, taking R.F=3/1. Show a distance of 47.8mm on this scale.

problem 4)(a) Sketch projections of the following points:

(i) Point A, 50mm in front of VP and 30mm above HP.

(ii) Point B, 40mm behind VP and 20mm below HP.

(b) A line AB, 35mm long is perpendicular to HP. Its end B is 15mm from HP and 20mm from VP. If the whole line lies in third quadrant, draw its projections. The line is parallel to VP.

problem 6) Demonstrate the following types of sections:

Half section, Partial or broken art Section, offset section, revolved section, removed section.

problem 7) A right circular cone of 30mm base diameter and 40mm height rests centrally on a square block of 50mm sides and 20mm thickness. Sketch isometric view of the assembly.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M98220

Have any Question?

## Related Questions in Mechanical Engineering

### Part 1 key engineering terms fill in the blanks -1

Part 1 Key Engineering Terms: fill in the blanks - 1. Phase: a _____________________________________ homogeneous and distinct portion of material system. 2. Degrees of freedom: number of variables that can be changed ___ ...

### A bar consists of two portions bc and c d of the same

A bar consists of two portions BC and C D of the same material and of the same length L, but of different cross sections. Determine the strain energy of the bar when it is subjected to an axial load P, expressing the res ...

### Design design all members of the 6 span truss each span is

Design: Design all members of the 6 span truss each span is 12 ft long, the height of the truss is 16 feet shown if w = 10,000 pounds. The allowable maximum tensile stress P/A is 1000 psi where P is the force in the memb ...

### A fan draws air from the atmosphere through a 030-mdiameter

A fan draws air from the atmosphere through a 0.30-mdiameter round duct that has a smoothly rounded entrance. A differential manometer connected to an opening in the wall of the duct shows a vacuum pressure of 2.5 cm of ...

### Two small cubes of equal size but made of different

Two small cubes of equal size but made of different materials are stacked (as shown in the figure below), so they just fit between two rigid surfaces. The bottom cube is subjected to a uniform pressure p on each of its e ...

### 1 the pump in the boat shown pumps 6 ft3nbsps of water

1. The pump in the boat shown pumps 6 ft 3  /s of water through a submerged water passage, which has an area of 0.25 ft 2  at the bow of the boat and 0.15 ft 2  at the stern. Determine the tension in the restraining rope ...

### Example how an p-channel flash eprom would work is the

Example how an p-channel flash EPROM would work. Is the p-channel worse or better than the n-channel asides form speed? Estimate the write and erase times (using the Fowler-Nordheim tunneling formulae for a triangular ba ...

### A transformer winding was designed to be fed by an ac

A transformer winding was designed to be fed by an ac voltage of 110 V and to produce an effective current of 10.5 A. By mistake, the transformer was fed from this same voltage but rectified in a full wave converter. Con ...

### 1 explain the read write erase operations of the fmosc

1. Explain the read, write, erase operations of the FMOSC memory cell shown in Fig. 674.4(b). Fig. 674.4 2. Is an initial charge up operation of the FMOSC memory cells necessary immediately after the d.c. power turned on ...

### Please reference any source of outside information as

Please reference any source of outside information as needed to answer these questions. 1. In a frozen food plant, atmospheric air is to go through a pre-cooler to be partially dehydrated so that during its passage throu ...

• 4,153,160 Questions Asked
• 13,132 Experts
• 2,558,936 Questions Answered

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen