Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1) State longitudinal vibrations.

b) prepare down the two uses of vibrations.

c) What do you mean by resonance

d) If mass of the vibrating body increases 9 times, what will be its effect on frequency.

e) State logarithmic decrement.

f) What is the angle between inertia and spring force?

g) What is the number of nodes if the shaft is having three rotors?

h) What is a continuous system?

i) Define principal mode of vibration.

j) What do you understand by semi definite system.

problem 2) prepare brief note on the following:

(a) Holzer's method.

(b) Vibrometer.

(c) Centrifugal pendulum vibration absorber.

problem 3) Derive a frequency equation of torsional vibrations for a free-free shaft of length l.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98197

Have any Question? 


Related Questions in Mechanical Engineering

The velocity profile in the annular control volume of

The velocity profile in the annular control volume of Example is approximately linear, varying from a velocity of zero at the outer boundary to a value of ωd/2 at the inner boundary. Develop an expression for the fluid v ...

Consider the top part of the balloon to be half of a

Consider the top part of the balloon to be half of a spherical pressure vessel. What is the ratio of the normal stress across a vertical seam to the normal stress across a seam inclined 45 degrees?

When choosing a bolting material we must consider its

When choosing a bolting material we must consider its affect on the clamping force to be created by those bolts in service. Name two important aspects of the clamping force which will be affected, in part at least, by th ...

Calculate the power factor of an electronic system subject

Calculate the power factor of an electronic system subject to a reasonable amount of harmonics given as THD(v) = 1.0%, the displacement factor is 0.92. What would be the calculated error if harmonic components were not t ...

You are asked to design a cylindrical scuba tank with a

You are asked to design a cylindrical scuba tank with a radius R = 16 cm to a pressure of p = 12.0 MPa at a factor of safety of 2.0 with respect to the yield stress. The relevant tabulated yield values for the steel of w ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

Example how an p-channel flash eprom would work is the

Example how an p-channel flash EPROM would work. Is the p-channel worse or better than the n-channel asides form speed? Estimate the write and erase times (using the Fowler-Nordheim tunneling formulae for a triangular ba ...

Determine the in-plane normal and shear stresses along the

Determine the in-plane normal and shear stresses along the seam of the tank of Problem 6.16 if it is helically wound at an angle θ = 60°. Problem 6.16: Determine the maximum in-plane stresses for a cylindrical tank made ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

The stepped shaft rotates at 120 rpm and has a 20 kw input

The stepped shaft rotates at 120 rpm and has a 20 kW input at A. 16 kW is taken off to operate machinery at B, and the remaining 4 kW is used at C. The shaft is stainless steel with yield strength in shear of 300 MPa. a. ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen