Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Briefly describe with the sketch of Electro hydraulic forming.

2) describe any two high velocity forming process or high energy rate forming process.

3) describe the different types of defects and their remedies in welding.

4) Define “Resistance Welding process”. With a help of neat sketch describe the spot welding method.

5) Discuss the following methods of inspection and Testing of castings.

a) Radio graphical testing

b) Ultrasonic testing.

6) Discuss with the help of diagram shell moulding method and prepare the advantages and disadvantages.

7) describe the working principle and construction features of Abrasive Jet Machining with illustrations.

8)  describe how EDM is capable of producing complex shapes.

9)  Classify and describe the different NC systems.

10) describe with neat sketch various components of NC Machines.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913557

Have any Question? 


Related Questions in Mechanical Engineering

A steel bar with the cross section shown and effective

A steel bar with the cross section shown and effective length L = 2.5 m is subjected to a compressive load P = 200 kN with a eccentricity e = 0.00625 m. Find (a) the beam's maximum deflection, and (b) the maximum normal ...

Describe the mil-std-1312 nas test name three generic ways

Describe the MIL-STD-1312 (NAS) test? Name three generic ways to prevent or at least minimize self-loosening? Define prevailing torque? A proper length-to-diameter ratio for the bolt can reduce or eliminate self-loosenin ...

1 if the density of sea water is approximated by the

1. If the density of sea water is approximated by the equation of stat is the compressibility, determine the pressure and density at a point 32,000 ft below the surface of the sea. Assume β = 300,00 psi. 2. The change in ...

As can often be seen in a kitchen sink when the faucet is

As can often be seen in a kitchen sink when the faucet is running, a high-speed channel flow (v 1 , h 1 ) may ''jump'' to a low-speed, low-energy condition (v 2 , h 2 ). The pressure at sections 1 and 2 is approximately ...

Assigned work clearly indicate all assumptions and

Assigned Work (Clearly indicate all assumptions and references) 1. A 500 m 2 light colored swimming pool is located at (a) normal suburban site, (b) well-sheltered site, where the measured wind speed at 10 m height is 3 ...

A rigid vessel of volume 0400 m3 containing h2 at 2125degc

A rigid vessel of volume 0.400 m3 containing H2 at 21.25°C and a pressure of 715 X 10 3 Pa is connected to a second rigid vessel of volume 0.750 m 3 containing Ar at 30.15°C at a pressure of 203 X 10 3 Pa. A valve separa ...

Please reference any source of outside information as

Please reference any source of outside information as needed to answer these questions. 1. In a frozen food plant, atmospheric air is to go through a pre-cooler to be partially dehydrated so that during its passage throu ...

1 the velocity vector in a two-dimensional flow is given by

1. The velocity vector in a two-dimensional flow is given by the expression v = 10e x  + 7xe y  m/s when x is measured in meters. Determine the component of the velocity that makes a 30° angle with the x axis at the poin ...

I need a proposal project for surface metrology asap i need

I need a proposal project for Surface Metrology ASAP. I need two documents: 1. Project outlines Proposal outlines (the instruction & template is in the attached Proposal for the project) should be 1 page 2. Final project ...

Need a 400 to 500 minimum word essay on 2 articles no

Need a 400 to 500 minimum word essay on 2 articles (No internet, just based on the articles) - You will need to do a compare and contrast essay where you compare an Old HVAC system with a New system and also old refriger ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen