Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1)(a) prepare down the different laws of thermodynamics and their limitations?

(b) Deduce the first law of thermodynamics for the open system.

2) Enthalpy of the binary liquid system of species 1 and 2 of fixed T and P is represented by equation.

H = 400x1+600x2+x1x2 (40x1+20x2)
Find out the numerical values for pure species enthalpies H1 and H2.

3) Determine the theoretical horse power needed to produce 400kg/hr of ice at 5oC from water at 15oC. Specific heat of ice and water are 2.1KJ/Kg.C and 4.2K/Kg.C and latent heat of fusion of ice is 320KJ/Kg. Suppose reversed carnot cycle.

4) Design neat and suiatble diagram for absorption refrigeration cycle and describe its working.

5)(a) Describe law of corresponding states in detail.

(b) Deduce a+b in terms of critical properties for Vander walls equation.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913450

Have any Question? 


Related Questions in Mechanical Engineering

How would you identify the best nut factor for your

How would you identify the best nut factor for your application? How much torque would be required to tighten an ASTM A193 Gr. B16 bolt with a 31/4-8 thread to 60% of yield? Why does a wrench create a side load on the bo ...

Part 1- heat1 the is used to express absolute temperatures

Part 1- Heat 1. The _______ is used to express absolute temperatures in the English system of measurement. A. Rankine scale B. Celsius scale C. Kelvin scale D. Fahrenheit scale 2. A silver bar 0.125 meter long is subject ...

1 a 1968 volkswagen sedan is driving over a 7300-ft-high

1. A 1968 Volkswagen sedan is driving over a 7300-ft-high mountain pass at a speed of v m/s into a headwind of W m/s. Compute the gage pressure in mPa at a point on the auto where the velocity relative to the auto is v - ...

The velocity profile in the annular control volume of

The velocity profile in the annular control volume of Example is approximately linear, varying from a velocity of zero at the outer boundary to a value of ωd/2 at the inner boundary. Develop an expression for the fluid v ...

In adiabatic demagnetization we use a magnetic ield to

In adiabatic demagnetization, we use a magnetic ield to couple away almost all of the residual energy of a crystal that has been cooled to 2.2 K by liquid helium. (We can get below the normal boiling point of liquid heli ...

At the end of a water pipe of 3-in diameter is a nozzle

At the end of a water pipe of 3-in. diameter is a nozzle that discharges a jet having a diameter of 1½ in. into the open atmosphere. The pressure in the pipe is 60 psig (pounds per square inch gage), and the rate of disc ...

A compute the intrinsic gate delay of the nmost given in

(a) Compute the intrinsic gate delay of the nMOST given in the above problem and also in section 661 at the biasing condition given above. (b) Compute the intrinsic power-delay product. (c) Does the load resistor increas ...

List three ways to control preload directly what are the

List three ways to control preload directly ? What are the advantages of a bonded ultrasonic transducer? What is sometimes cited as a disadvantage? Can torque be used to tighten a 6 in. diameter bolt? If not, why not? Na ...

Problem 1 -there is a circular combined open and closed

Problem 1 - There is a circular combined open and closed thin-walled section as shown in the figure. (R = 100mm, t = 2mm, S y = 100N) When shear force S y is applied to Web 24, calculate: a) Calculate I xx for the x-axis ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro