Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: Draw the elevation, plan and left-end view of the block shown below.

2175_left end view of block.jpg

problem 2: Draw the front view, top view and right-side view of the figure shown below.

1645_right view of block.jpg

problem 3: Draw the elevation, plan and left-side view of the figure described below.

2081_draw elevation.jpg

problem 4: Construct a diagonal scale of R.F 1:3200000 to show kilometers and long enough to measure up to 400 km. Show distances of 257 km and 333 km on the scale.

problem 5: Construct a diagonal scale to read up to 1/100th of a meter given R.F = 1/50 and to find out up to 7 m. Point out a distance of 5.45 m.

problem 6: Make a vernier scale to read meters, decimeters and centimeters and long adequate to measure up to 4m. R.F. of the scale is 1/20. Mark on the scale a distance of 2.28 m.

problem 7: Make a vernier scale to show readings of 1/10th of a meter when 3cm represents 10 m. Construct the scale to read up to 60 m and mark the distances of 35.3 m and 47.2 on your scale. 

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93737

Have any Question? 


Related Questions in Mechanical Engineering

Sea water rho 1025 kgm3 flows through a pump at 021 m3s

Sea water, ρ = 1025 kg/m 3 , flows through a pump at 0:21 m 3 /s. The pump inlet is 0.25 m in diameter. At the inlet the pressure is -0.15 m of mercury. The pump outlet, 0.152 m in diameter, is 1.8 m above the inlet. The ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

1 how do the magnitudes of the biceps force b and joint

1. How do the magnitudes of the biceps force B and joint reaction J change if the total weight w of the forearm and hand are included in the analysis and are assumed to be uniformly distributed over the forearm length L? ...

Each wood railroad tie supports part of the weight of a

Each wood railroad tie supports part of the weight of a train (plus the relatively small weight of a section of rail). This is modeled with two point loads representing the force of the rail on the tie. The reaction from ...

Use castiglianos second theorem to determine the tip

Use Castigliano's second theorem to determine the tip deflection of this cantilever with a length L, a constant E I, and a linearly increasing load with a maximum force/length q0. Confirm your result using Table 9.1.

A mixture of 210 x 10-3 g of o2 388 x 10-3 mol of n2 and

A mixture of 2.10 X 10 -3 g of O2 3.88 X 10-3 mol of N 2 . And 5.25 X 10 -3 molecules of CO are placed into a vessel of volume 5.25 L at 12.5°C. a. Calculate the total pressure in the vessel. b. Calculate the mole fracti ...

What do we mean by the term torque reaction a right angle

What do we mean by the term torque reaction? A right angle nut runner is used to produce 500 ft-lb of torque on a bolt having a 7/8 -9 UNC thread. The tool is 18 in. long. How much reaction force, created by the reaction ...

A rectangular brass column is loaded with a load of p 1500

A rectangular brass column is loaded with a load of P = 1500 lb applied 0.45 in off its centroidal axis. Find the longest permissible length L of the column if the deflection of its free end cannot exceed 0.12 in.

Define prying action sketch an alternative joint diagram

Define prying action? Sketch an alternative joint diagram showing the effects of prying action Name at least two things the joint designer can do to reduce prying action? This and the following three questions are all in ...

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro