Consider a family of logic gates that operates under, Ask an Expert

Engineering

Consider a family of logic gates that operates under thestatic discipline with the following voltage thresholds:VOL=0.5v, VIL=1.6v, VOH=4.4v, andVIH=3.2v
a) Graph an input-output voltage transfer function of aninverter satisfying the four voltage thresholds.

b) Using the switch-resistor MOSFET model, design an invertersatisfying the static discipline for the four voltagethresholds using an n-channel MOSFET with RN=1KΩand VT=1.8v. Recall, RON=RN(L/W).Assume VS=5v and Rsquare for a resistor is500Ω. Further assume that the area of the inverter is given bythe sum of the areas of the MOSFET and the resistor. Assumethat the area of a device is L x W. The inverter should takeas a little area as possible with minimum size for L or Wbeing 0.5μm. Graph the input-output transfer function fo the inverter. What is the total area of theinverter? What is its static power dissipation?

View complete question

Electrical & Electronics, Engineering

Category:- Electrical & Electronics
Reference No.:- M9873195

Have any Question?Write your Review or question?

Related Questions in Electrical & Electronics

Assignment -consider a common emitter amplifiernow lets say

Assignment - Consider a common emitter amplifier: Now let's say that R B and R C do a fine job at DC biasing the BJT but they are large so they can be neglected for small signal (AC) analysis. In that case, the equivalen ...

Problem 1 a two-phase servomotor has rated voltage applied

Problem 1: A two-phase servomotor has rated voltage applied to its excitation winding. The torque speed characteristic of the motor with Vc = 220 V, 60 Hz applied to its control phase winding is shown in Fig.1. The momen ...

Question -i a star-connected three-phase synchronous

Question - (i) A star-connected, three-phase synchronous induction motor takes a current of 10 amps from a 415 volt supply at unity power factor when supplying a steady load. If the synchronous reactance is 5 ohms/phase ...

Question 1 a pnp transistor withnbspbeta 60 is connected

Question 1. A pnp transistor with β = 60 is connected in a common-base configuration as shown in figure P5.8 (a) The emitter is driven by a constant-current source with I E = 0.75 mA. Determine I B , I C , α, and V C . ( ...

Summative assessmentin 2017 sej101 assessment will consist

Summative Assessment In 2017 SEJ101 assessment will consist of nine tasks that will develop a portfolio of your assessed work. Throughout the trimester you will have the opportunity for feedback on all nine tasks before ...

Advanced computational techniques in engineering assignment

Advanced Computational Techniques in Engineering Assignment - Optimisation For this assignment, you are required to carry out the process of attempting to solve different optimisation problems. For each question, you are ...

Discuss the role of load factor on the cost of electrical

Discuss the role of load factor on the cost of electrical energy.

Questions -q1 a single-phase transformer rated 21 kv130 v

Questions - Q1. A single-phase transformer rated 2.1 kV/130 V, 7.8 kVA has the following winding parameters: r1= 0.7Ω, x1 = 0.9Ω, r2 = 0.04Ω and x2 = 0.05Ω. Determine: a. The combined winding resistance ________ Ω and le ...

Questions -problem 1 - a series rlc network has r 2 komega

Questions - Problem 1 - A series RLC network has R = 2 kΩ, L = 40 mH and C = 1μF. Calculate the impedance at resonance and at one-fourth, one-half, twice, and four times the resonant frequency. Problem 2 - Design a serie ...

Case studythis assignment consists of a written report of

CASE STUDY This assignment consists of a written report of approximately 1000 words and any diagrams in which you are asked to critically compare different process methods used to achieve the same result and show an awar ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Electrical & Electronics Expert