Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: Categorize milling machines and list them accordingly. How milling operation distinct from turning operation on lathe?

problem 2: describe the main parts of a slotting machine. describe at least three kinds of slotting machine of them.

problem 3: How the size of a planer is specified? List out and describe the major parts of a planer.

problem 4: List out different mechanisms for table drive in shaper. describe one mechanism with simple sketch.

problem 5: What are the various horizontal boring machines? List them and specify their suitability.

problem 6: describe the different types of operation which can be performed by a vertical boring machine.

problem 7: Name different types of drilling machines. How the size of a drilling machine is specified? describe the various drilling operations.

problem 8: What is the major function of a lathe? State the operations which might be performed on a lathe.

problem 9: What do you mean by the word casting? What is a pattern? Describe the factors on which the types of patterns depend.

problem 10: How are manufacturing processes categorized? What points must be considered for selecting a manufacturing process? List out the activities and operations included in manufacturing.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M92678

Have any Question? 


Related Questions in Mechanical Engineering

One excited state of the sodium atom lies at 25 73986 cm1

One excited state of the sodium atom lies at 25 739.86 cm1 above the ground state, another lies at 50 266.88 cm-1 . Suppose they are connected by a perturbation equivalent in energy to (a) 100 cm -1 , (b) 1000 cm -1 , (c ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

3-5 a water-tube steam generator operating at 2400 psia

3-5 A water-tube steam generator operating at 2400 psia has 50-ft-high 3-in ID tubes. The pressure Drop is given by 3.25 x 10- 6 m 2, where m is the mass flow rate, in pound mass per hour Assuming sanzati water in the do ...

Determine the tip deflection of a beam with linear varying

Determine the tip deflection of a beam with linear varying width b(x), constant height h, length L, and elastic modulus E due to tip load P. Write the answer in terms of the maximum width b L = b(L). Also determine the n ...

1 sketch the deformation of a fluid element for the

1. Sketch the deformation of a fluid element for the following cases: 2. For a two-dimensional, incompressible flow with velocity v x  = v x (y), sketch a three-dimensional fluid element and illustrate the magnitude, dir ...

An athlete at high performance inhales of air at 100 atm

An athlete at high performance inhales of air at 1.00 atm and 298 K. The inhaled and exhaled air contain 0.50 and 6.2% by volume of water, respectively. For a respiration rate of 32 breaths per minute, how many moles of ...

The illustration below shows a vane with a turning angle

The illustration below shows a vane with a turning angle θ which moves with a steady speed v c . The vane receives a jet that leaves a fixed nozzle with speed θ. (a) Assume that the vane is mounted on rails as shown in t ...

A sample of propane c3h8 is placed in a closed vessel

A sample of propane (C 3 H 8 ) is placed in a closed vessel together with an amount of O 2 that is 2.15 times the amount needed to completely oxidize the propane to CO 2 and H 2 O at constant temperature. Calculate the m ...

1 using the expression for the gradient in polar

1. Using the expression for the gradient in polar coordinates (Appendix A), find the gradient of ψ(r,θ) when Where is the gradient maximum? The terms A and a are constant. 2. Given the following expression for the pressu ...

A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro