+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1: As shown in the sketch, water at 20° C is being pumped from a lower tank and discharged into the atmosphere 10 meters above the level of the tank. The flow rate is 1200 liters/minute. There is a negligible amount of 5 inch schedule 40 commercial steel pipe between the tank and the pump containing a square edged entrance, a ball check valve, two standard elbows and a strainer with a loss coefficient, K, of 3.0. The pump suction is three (3) meters above the level of the tank. The discharge pipe is 50 meters of 3.5 inch schedule 40 commercial steel pipe, containing a globe valve, a straight flow tee and two standard elbows.

a) find out the head provided by the pump (m).

b) find out the brake power required if the pump efficiency is 75% (kW).

c) find out the net positive suction head available (NPSHA) if the atmospheric pressure is 100 kPa. (m)

problem 2: You Already find outd one point of HA at various flow rates for the system curve. Develop the system curve by calculating HA at various flow rates for the system given, and plot the values on attached Pump Characteristic Curve and determine

a) The flow rate (1min) ________, head (m), ___________and BHP (kw) __________at which this pump will operate in the sytem.

b) With the pump curves given, develop an efficiency curve for the pump and determine the maximum efficiency and the efficiency at which the pump system will operate. ____________

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M96011

Have any Question?

## Related Questions in Mechanical Engineering

### Define prying action sketch an alternative joint diagram

Define prying action? Sketch an alternative joint diagram showing the effects of prying action Name at least two things the joint designer can do to reduce prying action? This and the following three questions are all in ...

### 1 gas turbine and compressed air systems will serve as

1. Gas turbine and compressed air systems will serve as prime movers at a very high speed. Discuss the design characteristics of an induction generator for those applications. 2. Explain in detail why induction generator ...

### Residential water use exclusive of fire protection runs

Residential water use, exclusive of fire protection, runs about 80 gallons per person per day. If the water is delivered to a residence at 60 psig, estimate the monthly energy required to pump the water from atmospheric ...

### We want to tighten an astm a193 bolt having 4-8 un threads

We want to tighten an ASTM A193 bolt having 4-8 UN threads and a yield strength of 96 ksi. The effective length of its body, Lbe, is 12 in.; that of its threads, Lse, is 4 in. We're going to control the buildup of preloa ...

### Calculate the total lift force on the arctic hut shown

Calculate the total lift force on the Arctic hut shown below as a function of the location of the opening. The lift force results from the difference between the inside pressure and the outside pressure. Assume potential ...

### Write one page paper explaining the bad emissions that are

Write one page paper explaining the bad emissions that are emitted by the automotive engine and how are they reduced before entering atmoshere?

### A cantilever beam ab supports a uniform load of intensity q

A cantilever beam AB supports a uniform load of intensity q acting over part of the span and a concentrated load P acting at the free end, as shown. Determine the deflection and slope at end B of the beam. The beam has l ...

### 1 determine the capillary rise for a water-air-glass

1. Determine the capillary rise for a water-air-glass interface at 40°C in a clean glass tube having a radius of 1 mm. 2. Determine the difference in pressure between the inside and outside of a soap film bubble at 20 °C ...

### A room has design conditions of78 f db and 50 rh and a rscl

A room has design conditions of78 F DB and 50% RH and a RSCL = 18,000 BTUlhr and RLCL = 8000 BTUlhr. An air conditioning unit supplies 900 CFM of air to the room at 58 F DB and 56 F WB. Will the unit maintain the room de ...

### 1 concrete rocks and bone are strong in compression and are

1. Concrete, rocks, and bone are strong in compression and are usually designed for compressive loading. To test their strength in compression, what sort of test specimen would be useful? 2. Suppose that a downward force ...

• 4,153,160 Questions Asked
• 13,132 Experts
• 2,558,936 Questions Answered

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro