+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1:

Consider the polar coordinate system drawn in space about circular cylinder. Describe this system in relation to general idea of boundary fitted coordinate system.  Also compute the metrics for this system.

problem 2:

prepare down an account on the:

(a) Lax-Wendroff Technique and

(b) MacCormack’s Technique.

problem 3:

Illustrate how the lift generated on the arbitrary body by using the vortex panel method.

problem 4:

Using source panel technique, estimate the forces acting on the circular cylinder which is sinusoidally oscillating perpendicular to free stream direction.

problem 5:

Verify that node centered Finite volume technique formulation yields the result identical to finite difference technique for rectangular grids.

problem 6:

By using Cell – centred average scheme, reprepare Euler equation for the transonic and supersonic flows.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M912433

Have any Question?

## Related Questions in Mechanical Engineering

### Salt water containing 192 lbgal of salt flows at a fixed

Salt water containing 1.92 lb/gal of salt flows at a fixed rate of 2 gal/min into a 100-gal tank, initially filled with fresh water. The density of the incoming solution is 71.8 lb/ft 3 . The solution, kept uniform by st ...

### Part 1 key engineering terms fill in the blanks -1

Part 1 Key Engineering Terms: fill in the blanks - 1. Phase: a _____________________________________ homogeneous and distinct portion of material system. 2. Degrees of freedom: number of variables that can be changed ___ ...

### Compute the shear strengths of those two threads if the

Compute the shear strengths of those two threads if the fasteners are made from Grade 8 material? Compute the ratio between shear strength and proof strength for each of these two threads ? A threaded fastener will often ...

### For the state of stress given in problem 517 determinea the

For the state of stress given in Problem 5.17, determine a. the maximum shear stress b. the normal stresses on the plane of maximum shear stress c. the normal and shear stresses after the element has been rotated through ...

### Assignmentfor this homework you will be creating scripts in

ASSIGNMENT For this homework you will be creating scripts in SciLab. You will turn in electronically, each of the scripts requested below. This is not a group project, so do your own work. Contact me if you have any ques ...

### Calculate the fraction of n2 molecules in a sample at 298 k

Calculate the fraction of N2 molecules in a sample at 298 K that have speeds less than 10.0ms -1 by integrating the Maxwell-Boltzmann distribution over the appropriate range of speeds (just writing the correct integral i ...

### Define the endurance limit of a bolt which is greater the

Define the endurance limit of a bolt ? Which is greater, the static yield strength or the endurance limit of the bolt? When will an increase in preload increase fatigue life? When will an increase in preload decrease fat ...

### A cantilever beam ab supports a uniform load of intensity q

A cantilever beam AB supports a uniform load of intensity q acting over part of the span and a concentrated load P acting at the free end, as shown. Determine the deflection and slope at end B of the beam. The beam has l ...

### Projectdesign a tube bank that will increase the

Project Design a tube bank that will increase the temperature of a 1200 CFM flow of air from 35°F to 100°F. Assume a constant pressure of 1atm. Each tube will have a diameter of 0.5in and a length of 24in. The tube confi ...

### 1 identify the terms that may arise from the ground

1. Identify the terms that may arise from the ground configurations of the atoms of elements of Period 2 and suggest the order of their energies. 2. Find the first-order corrections to the energies of the hydrogen atom t ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro