Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Answer the following problems.

problem 1) What do you understand by orbital spacing? Why it is required?

problem 2) Why downlink design is difficult than uplink design?

problem 3) Describe the term: beam acquisition in detail.

problem 4) describe CATV system in brief.

problem 5) prepare down the significance of noise figure.

problem 6) Describe in brief the advantages of CDMA over FDMA.

problem 7) How does satellite communication help in scientific study?

problem 8) Which kind of communication is best suited for long distance?

problem 9) prepare down the advantages of satellite communication.

problem 10) Briefly describe the use of tracking and pointing in satellite communication.

problem 11) describe in detail about DA-FDMA (SPADE) system. In what ways it is different from simple FDMA system.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M98468

Have any Question? 


Related Questions in Electrical & Electronics

1 the stream function for an incompressible two dimensional

1. The stream function for an incompressible, two dimensional flow field is For this flow field, sketch several streamlines. 2. A line vortex of strength K at (x, y) = (0, a) is combined with opposite strength vortex at ...

1 what is the total distance around the circumference of a

1. What is the total distance around the circumference of a circle of radius 1 m? What is the total vector distance around the circle? 2. What is the total surface area of a cube of sides 1 m? Assuming the normals to the ...

State with reasons whether the following signals are

State with reasons whether the following signals are periodic or aperiodic. For periodic signals, find the period and state which of the harmonics are present in the series.

A a signal x t 5 sinc2 5pit cos 20pit is sampled at a

a. A signal x (t) = 5 sinc 2 (5πt) + cos 20πt is sampled at a rate of 10 Hz. Find the spectrum of the sampled signal. Can x (t) be reconstructed by lowpass filtering the sampled signal? b. Repeat part (a) for a sampling ...

1 implement the half adder circuit on the breadboard2

1. Implement the half adder circuit on the breadboard. 2. Implement the full adder circuit on the breadboard. 3. Using the 2-bit adder presented in the chapter as a model, implement a 4-bit adder in Logisim. Implement an ...

1 in an impulse invariance design show that if has is a

1. In an impulse invariance design, show that if Ha(s) is a transfer function of a stable system, the corresponding H[z] is also a transfer function of a stable system. 2. First-order backward differences provide the tra ...

1 in polar coordinates show that2 determine the fluid

1. In polar coordinates, show that 2. Determine the fluid rotation at a point in polar coordinates, using the method illustrated in given figure.

Figure 319 in the text shows that des creates 16 different

Figure 31.9 in the text shows that DES creates 16 different 48-bit keys, one for each round. Why do we need 16 different keys? Why can't we use the same key in each round?

A force f is applied at the tip of the uniform bar shown in

A force F is applied at the tip of the uniform bar shown in the figure. The displacement of the bar is given as u(X) = λX where λ is the principal stretch. The initial length and the cross-sectional area of the bar are, ...

Diode circuits1 the 6v zener diode below has zero zener

Diode Circuits 1. The 6V zener diode below has zero Zener resistance and a knee current of 5mA.The minimum value of R, so that the voltage across it does not fall below 6V is 2.A zener diode in the circuit shown in below ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen