Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1) prepare detailed notes on digital comparator.

problem 2) Draw the circuit diagram of RTL gate. Describe its working.

problem 3) Describe the function of MOSROM with a well labelled circuit diagram.

problem 4) Briefly describe the BJT RAM.

problem 5) What is compact disk? Describe.

problem 6) Describe the medical application of Laser.

problem 7) State and describe the function of Photo detector.

problem 8) prepare down a detailed note on E-mail and FAX.

problem 9) Describe in detail the classification, characteristics and parameters of Digital IC’s.

problem 10) Draw the circuit and describe the working of the following:

(i) DTL gate,

(ii) TTL gate.

problem 11) Describe the following semiconductor memories with appropriate diagram.

(i) PROM

(ii) EPROM

(iii) EEPROM

problem 12) With logic circuit diagram, describe the working of Programmable Logic Array.

problem 13) prepare a detailed note on the following:

(i) Winchester disk

(ii) Compact Disk

(iii) Mouse

(iv) MODEM

problem 14)(i) Describe the fibre optic fabrication technology and describe its relative merits and demerits.

(ii) prepare a short note on Pulse code modulation.

problem 15) Describe the principle of satellite communication. describe the different parts of satellite communication system.

problem 16) describe with a circuit diagram the principle and working of SMPS power supply. prepare down its advantages.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M97636

Have any Question? 


Related Questions in Electrical & Electronics

1 what is the particular advantageous characteristic

1. What is the particular advantageous characteristic associated with the unit vectors in the Cartesian coordinate system? 2. How do you find a vector perpendicular to a plane? 3. How do you find the perpendicular distan ...

In digital communication systems transmission of digital

In digital communication systems, transmission of digital data is encoded using bandlimited pulses in order to utilize the channel bandwidth efficiently. Unfortunately, bandlimited pulses are nontimelimited; they have in ...

1 in kademlia assume m 4 and active nodes are n4 n7 and

1. In Kademlia, assume m = 4 and active nodes are N4, N7, and N12. Where is the key k3 stored in this system? 2. In Chord, assume the size of the identifier space is 16. The active nodes are N3, N6, N8, and N12. Show the ...

Diode circuits1 the 6v zener diode below has zero zener

Diode Circuits 1. The 6V zener diode below has zero Zener resistance and a knee current of 5mA.The minimum value of R, so that the voltage across it does not fall below 6V is 2.A zener diode in the circuit shown in below ...

In rsa given p 107 q 113 e 13 and d 3653 encrypt the

In RSA, given p = 107, q = 113, e = 13, and d = 3653, encrypt the message "THIS IS TOUGH" using 00 to 26 (A: 00 and space: 26) as the encoding scheme. Decrypt the ciphertext to find the original message.

Compute and plot the solution of the difference equation yn

Compute and plot the solution of the difference equation y[n] þ y[n 1] = 2x[n] þ x[n 1], where x[n] = 0.8n u[n] assuming zero initial conditions. Moreover, verify your answer (a) by examining if the derived solution sati ...

1 explain the self-consistency condition for waveguiding in

1. Explain the self-consistency condition for waveguiding in a dielectric slab waveguide. 2. Discuss the dependence of the number of propagating modes in a dielectric slab waveguide on the ratio of the thickness d of the ...

1 the rocket nozzle shown below consists of three welded

1. The rocket nozzle shown below consists of three welded sections. Determine the axial stress at junctions 1 and 2 when the rocket is operating at sea level. The mass flow rate is 770 lb m /s. 2. The pressure on the con ...

1 briefly discuss the solution of the transmission-line

1. Briefly discuss the solution of the transmission-line matching problem. 2. How is the length of a short-circuited stub for a required input susceptance determined by using the Smith Chart?

A force f is applied at the tip of the uniform bar shown in

A force F is applied at the tip of the uniform bar shown in the figure. The displacement of the bar is given as u(X) = λX where λ is the principal stretch. The initial length and the cross-sectional area of the bar are, ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro