Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

a.The closest point to discharge treated effluent is a lake, but the pipeline is extended so it discharges into the river draining the lake. This allows a conventional secondary treatment level (Table 11-6) and not be required to also reduce NH3, TKN and P, as per Table 11-7. Explain why the difference in receiving waters affects the treatment required.

b. Influent wastewater SS or TSS = 220 mg/l. Primary sedimentation removes 60% of it. The sludge has 6% solids. Calculate the daily volume (liters) and dry solids weight (kg) of primary sludge.

c. The hydraulic detention time F/M= 4 hours, the overflow or surface settling rate is v0 =500 gpd/ft2. Compute the volume and depth of the sedimentation tank.

d. Say the organic SS particles have specific gravity Gs = 1.1. The inorganic SS particles have Gs= 2.65. For which type of material are the removed particles of larger diameter? Illustrate by formula.

e. Activated sludge treatment is used. 2.0 mgd inflow to the aerobic reactor has 100 mg/l BOD5 (So). How many pounds of air at 20% O2 must be transferred into the wastewater each day?

f. Using same F = Q x So, it's desired to keep F/M= 0.2 in the 40,000 ft3tank. Find the desired X (VSS concentration) that must be maintained. Sketch the system used to keep reactor aerated, mixed, and at X.

g. The microorganisms doing the treatment are endogenous, chemheterotrophs Explain what each of these descriptors of metabolism means.

h. The COHNS substrate includes both VS and FS content. What are the 3 possible fates? Yield = 40%. If its 100% degraded (just VS), how many moles of CO2 are produced per mole substrate?

i. Primary & secondary sludge are blended and anaerobically digested in a closed tank for θ = 20 days to reduce VSS. How does this help the plant to be energy self-sufficient?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M9525727

Have any Question?


Related Questions in Mechanical Engineering

Problem on shaft -assuming no frictional losses a torque of

Problem on Shaft - Assuming no frictional losses, a torque of T = 750lb·in is applied through the shaft of gear F in order to drive the roller chain at point B at a constant speed. The chain sprocket has a pitch diameter ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Structural mechanics questions -q1 a 150-lb bucket is

Structural Mechanics Questions - Q1. A 150-lb bucket is suspended from a cable on the wooden frame. Determine the resultant internal loadings on the cross section at D, and at E. Q2. The shaft is supported at its ends by ...

Fluid mechanics assignment - finite control volume analysis

Fluid Mechanics Assignment - Finite Control Volume Analysis and Dimensional Analysis Q1. The wind blows through a 7ft × 10ft garage door opening with a speed of 5 ft/s as shown in the figure. Determine the average speed, ...

Expansion processes of a perfect gasassignment1 attend the

Expansion Processes of a Perfect Gas Assignment: 1. Attend the laboratory class and complete the lab tests according to the supervisor's requirement. Students will not allowed to submit their report if they do not come t ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As