Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Q1. Should the ventilation blower be running in the supply mode or exhaust mode, if the Oxygen check is completed?

Q2. In a tanker, describe why are bonding straps used on the cargo pipelines?

Q3. Illustrate the rating of the electrical hand glove?

Q4. Illustrate the significant first aid for an electrical shock victim?

Q5. Is there any protection for the CO2 cylinder in case of fire in the CO2 room itself?

Q6. Is CO2 in the bottle in liquid or gas form or condition?

Q7. describe how does the CO2 alarm ring if the panel door is opened?

Q8. Can engine room bilges be pumped out in the special areas?

Q9. All through your watch, if you find a under piston temperature high alarm, describe what will you do?

Q10. Throughout your night duty on a UMS vessel, there is a fire alarm from E/R. Illustrate your action in case of:

a) Purifier room fire
b) Running generator exhaust manifold on fire
c) Boiler front on fire
d) Bilges on fire

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911361

Have any Question? 


Related Questions in Mechanical Engineering

1 a venturi meter with an inlet diameter of 06 m is

1. A Venturi meter with an inlet diameter of 0.6 m is designed to handle 6 m3 /s of standard air. What is the required throat diameter if this flow is to give a reading of 0.10 m of alcohol in a differential manometer co ...

1 estimate the viscosity of nitrogen at 175 k using given

1. Estimate the viscosity of nitrogen at 175 K using given equation. 2. Calculate the viscosity of oxygen at 350°K and compare with the value given in Appendix I. 3. What is the percentage change in the viscosity of wate ...

1 explain the read write erase operations of the fmosc

1. Explain the read, write, erase operations of the FMOSC memory cell shown in Fig. 674.4(b). Fig. 674.4 2. Is an initial charge up operation of the FMOSC memory cells necessary immediately after the d.c. power turned on ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

1 the hypodermic needle shown below contains a liquid serum

1. The hypodermic needle shown below contains a liquid serum (ρ = 1 g/cm 3 ). If the serum is to be injected steadily at 6 cm 3  /s, how fast should the plunger be advanced (a) if leakage in the plunger clearance is negl ...

Name the two types of bolted joints and tell why theyre

Name the two types of bolted joints and tell why they're called that? What is the main mission of the bolts in any joint? What factor largely determines the behavior and life of a tensile joint? Why are bolted joints oft ...

Now consider a second joint of the same material width and

Now consider a second joint of the same material, width and thickness as the joint in problem 4 above but eccentrically loaded. This time, however, the line of action of the external load is 0.563 in. removed from the ce ...

In problem compute the upward force on the device from

In Problem, compute the upward force on the device from water and air. Use the results of Problem as well as any other data given in that problem that you may need. Explain why you cannot profitably use Bernoulli's equat ...

For the allen wrench of problem 715 what is the deflection

For the allen wrench of Problem 7.15, what is the deflection of the tip of the wrench when the maximum load of 60 N is applied, just before the bolt loosens? Problem 7.15: The maximum force applied to the tip of the alle ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen