+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1: A circular lamina of 60 mm diameter rests on HP on a point 1 of its circumference. The lamina is inclined to HP in such as way that the top view of it is an ellipse of minor axis 35 mm. The top view of the diameter through the point 1 makes an angle of 45o with VP. Draw the projections and find out the angle of plane made with the HP.

problem 2: A thin rectangular plate of sides 60 mm x 30 mm has its shorter side in VP and inclined at 30o to HP. Project its top view if the front view is a square of 30 mm long sides.

problem 3: A semi-circular lamina of diameter 64 mm diameter has its straight edge in VP and inclined at an angle of 45o to HP. The surface of lamina makes an angle of 30o with the VP. Draw its projections.

problem 4: A square lamina PQRS of side 40 mm rests on ground on its corner P in such a manner that the diagonal PR is inclined at 45o to the VP and apparently inclined at 30o to the VP. Draw its projections.

problem 5: A pentagonal plate of side 30 mm is resting on the HP on one of its corners with its surface inclined at 45o to HP. The side opposite to resting corner is parallel to Vp and farther away from it. Sketch its projections.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M93740

Have any Question?

## Related Questions in Mechanical Engineering

### A nut having an effective length of 2 in and a 12-16 un

A nut having an effective length of 2 in. and a 1/2-16 UN thread is snug tightened and then turned 308. How much preload will that create in the bolt? Is that an acceptable preload? Describe the typical torque-turn tight ...

### You have been introduced to a number of different tools

You have been introduced to a number of different tools that can be used to help IE's and MfgE's analyze and develop solutions to make processes more effective and efficient. Watch the video located at http://www.iienet2 ...

### Project -this project is individual work write a computer

Project - This project is individual work. Write a computer program using Matlab to read the engineering constants E 1 , E 2 , v 12 , and G 12 then computes and prints the Reduced Compliances Matrix [S], the Reduced Stif ...

### 1 a cylindrical pressure vessel with hemispherical endcaps

1. A cylindrical pressure vessel with hemispherical endcaps has radius r = 2 m, wall thickness t = 10 mm, and is made of steel with yield stress σy = 1800 MPa. It is internally pressurized at p = 2 MPa. Compare the Tresc ...

### Question 1derive an expression for the velocity vector of

Question 1: Derive an expression for the velocity vector of the collar D, N V D. The upper arm (B) rotates about a horizontal axis ( nˆ x ) at a rate q · 1 The lower arm (C) Rotates about the longitudinal axis of B (bˆ z ...

### Consider the phase diagram for 4hea how many phases are

Consider the phase diagram for 4He a. How many phases are shown? b. How many triple points are shown? c. What is the boiling point of helium at 0.01 bar? d. What are the possible phase transitions?

### A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

### How would you identify the best nut factor for your

How would you identify the best nut factor for your application? How much torque would be required to tighten an ASTM A193 Gr. B16 bolt with a 31/4-8 thread to 60% of yield? Why does a wrench create a side load on the bo ...

### 1 if the design load is 90 kn 20300 lbf what is the dead

1. If the design load is 90 kN (20,300 lbf), what is the dead load and what is the intensity of the dead load in the light of the live load calculation of Problem CS1.1? 2. Determine the specific weight of lightweight co ...

### 1 using the expression for the gradient in polar

1. Using the expression for the gradient in polar coordinates (Appendix A), find the gradient of ψ(r,θ) when Where is the gradient maximum? The terms A and a are constant. 2. Given the following expression for the pressu ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro